Advice 1: How to connect two TVs to a satellite dish antenna

The world has moved forward far enough. Before, only a few decades ago, the TV had only dreamed of. Today there is an opportunity to buy several televisions for one family. Every TV has certain characteristics making channels to broadcast. To take greater and greater number of channels allows satellite dish. You can choose a package of channels, the conditions of transmission, the satellite connection for the antenna. In addition, today it is possible from one satellite dish to connect two TVs. To make such a connection independently with some fairly simple knowledge of electronics.
You will need
  • Satellite antenna (dish), the Converter Ku band, receiver, cable and a choice of mounting plates, basic skills of working with electronics.
Instruction
1
When deciding how to connect two TVs to one satellite dish antenna is to determine the package of channels. One option may be the TRICOLOR. He broadcasts from the satellite Eutelsat W4 in good gear. Satellite antenna may be 60 cm diameter, offset type. Her antenna are arranged vertically. This allows you to take a good signal.
2
The Converter range and the receiver are used for signal conversion. It moves from a higher frequency to a lower frequency. The solution of viewing the scrambled channels will require installation of additional hardware – decoder. The receiver connects directly to the TV through the antenna input.
3
When selecting the cable particular attention should be paid to its quality. Not worth saving. It is from the high signal quality determines the amount of data loss. It is necessary to take into account the stream on TV. It can hold one or two connectors.
4
The antenna is fitted with two tuner. The variant of the connection heads on the antenna. It should connect using "Switch" so-called DoppelgangeR to split the signal. He has usually one input from the antenna and two outputs for TVs.
5
After all operations you can customize through the antenna satellite Internet. Its speed is much higher than usual.
Note
You need to pay attention not only to the manufacturer. A good solution would be to test the compatibility of the antenna, additional heads, receiver, tuner, and cable televisions. This will avoid disruptions in receiving and distribution of signals.
Useful advice
The decision to choose to connect a satellite antenna to two TVs, you should carefully approach the selection of components parts to the whole structure. This is especially true of the antenna itself.

Advice 2: How to connect your TV to the antenna

In order to television began to take the channels, just enough to bring it into the room and to include. It is also necessary to connect the antenna. From the correct choice depends on the number of received channels and the quality of their reception.
Instruction
1
Remember the cardinal rule: if the braid of the antenna cable is grounded (if the antenna collective, it is always so, but often it is grounded and from individual external antennas), touch both metal elements plugged in the TVand plug when they are not connected, it is impossible! It is also impossible to touch both metal parts of the two plugged in and not connected to each other devices (e.g., TVand DVD player) and connected the cables, even if the antenna is not grounded. In addition, you can not touch the metal parts of the TVand any video equipment, and antenna cable telescopic antenna in the case if your body has acquired an electrostatic charge from the screen CRT TV (e.g. wiping).Never install an outdoor antenna yourself, if you are not sure that will be able to provide reliable lightning protection. Solder the cables to any grounded antennas only soldering irons with proper insulation.
2
In order to connect to the TVhave a built-in adenostyletea telescopic antenna, insert the plug coming from the body of the device on the wire to its antenna socket. If there are two nests corresponding to different ranges, move this plug to the one that corresponds to the range in which you are currently receiving.
3
If to the TVhave also attached a ring antenna, built-in telescopic plug in to the socket corresponding to the metric wave band, and the ring - to the socket corresponding to the range of decimeter waves. Some TVs, the second antenna will be to keep straight on the nest, while others will have to consolidate at first.
4
If the TVhave a two-pin attached telescopic antenna, attach sasima out symmetrical ribbon cable, a special adapter-soglasovatel, if you haven't done so already. Then connect the adapter to the antenna Jack on the TVand (in these machines it is usually one).
5
If an indoor or outdoor antenna is an all-wave, and TVand separate entrances for antenna ranges VHF or UHF, use a dividing splitter. Similarly, if the TVhas a input for the wave aerials, and you have two separate antenna bands VHF and UHF, use a unifying splitter. Both devices are sold in hardware stores.
6
To connect one antenna to multiple TVam use another device, called CRAB cable splitter subscriber household). It is also sold in hardware stores. Best of all this unit works with collective antenna.
7
To use an antenna with amplifier, after its connection to the TVat turn on the socket power supply. Turn it off simultaneously with the TVom.
8
To connect a satellite dish to the TVfrom directly. Use the satellite receiver. To mount it, special knowledge is almost not needed (all described in the instructions and on websites), but they are required for the successful guidance of the "plates" to the satellite.

Advice 3: How to connect two TVs to one cable

To connect multiple TVs to one cable can be used different ways. Connectivity option depends on the ultimate goal of performing this connection.
You will need
  • - splitter.
Instruction
1
If you need to connect your TV to the same cable TV wire, then use a special splitter. This device is a kind tee, * branching coaxial cable. Connect one end of the splitter to the desired cable, and the remaining free slots connect with a TV using the right cables.
2
If you are using a receiver for obtaining access to satellite TV, then purchase an additional splitter. A lot depends on which channel you choose to connect the receiver to the TV. Currently freely available, you can easily find the splitters ports, VGA and DVI. Connect the accessory cable coming from the receiver. Connect it to your TV.
3
Remember that you can use additional adapters, allowing to connect the ports of VGA, DVI and HDMI together. Purchase any set of adaptors. Note that the use of these accessories significantly reduces the quality of the transmitted signal. Remember that under this option, connect the TV to a single cable, both devices will show a single channel.
4
Use splitter port VGA or DVI to connect the TV to the same connector of the graphics card of the computer. In this case, both devices will be identical signal, which is not always convenient.
5
The optimal solution is to use two types of connection. Connect the coaxial cable of a conventional antenna to both TVs by the method described above. Connect both devices to the receiver. This method will allow you the right time to switch the operating mode of the TV (receiver/antenna), thus providing you with the ability to select the desired channel. If you want to connect both TVs to satellite television, choose the company that installs their own single receiver serving the building or the entrance.

Advice 4: As one satellite dish to connect two TVs

If one satellite dish and two TVs, to get them to work from one of the "plates". But will either have to use two receivers or put up with the inability to watch one TV, one satellite channel, and the other two.
Instruction
1
Use receivers to connect two TVs. If one of the receivers has not only input but also output antenna connector (not to be confused with nest modulator for connection to TV's RF output), connect this Jack with a cable that is certified for the connection of satellite antennas receivers to the input Jack of the second receiver. We obtain a chain: the Converter is the first receiver or second receiver. Note that if you take the scrambled channels, you will have to buy two cards and pay the license fee for each of them. Also you cannot look at one receiver channels require vertical polarization, and the other requiring horizontal.
2
You can use a splitter, also certified for use with satellite receivers and converters. Normal television will not work - it does not pass the supply voltage required by the Converter, and the switching voltage of the polarization. This option imposes the same limitations as the previous one. And since additional hardware is required, apply it in the case if none of the receivers has an output socket to connect a second device.
3
Install the two antenna Converter, and you will be able to connect one of them to one receiver and the other to another. To use them you will be able independently, but to send both units to the same satellite is impossible. Will have to watch the same TV channels from one satellite and the other from another. Card, if the coded channels, you will also need two, and the monthly fee make have both.
4
Another connection method is to use a Converter with two outputs. One of them allows you to receive only channels with horizontal polarization, the other with only vertical. Both outputs of the Converter connect to the device called multiswitches. And multiswitch one to three receivers, TVs. Any of them can independently watch channels broadcasting at any polarization, but all required switching will automatically make multivits. But card for receiving encrypted channels will still need as much as receivers, and will have to pay for each of them.
5
If you wish to provide one receiver and one card, and the receiver is equipped with a high-frequency modulator, connect the modulator output to two TVs through a splitter, designed for ground-based antennas. Both the TV set to a channel broadcast by the modulator. But now, if you switch the received channel on the receiver, it will be replaced at the same time on both televisions.
6
You can also connect one TV at a low frequency (through the RCA connectors or SCART) and the second high - through the modulator. The result will be the same, but on the ground of the TVs will also independently take air TV channels by plugging in an indoor or outdoor antenna. And if you connect one TV to the receiver via SCART, and the second via RCA, then connect the antenna for reception of terrestrial TV channels, it will be possible to both vehicles.
Note
All switch do pre-de-energized equipment.
Search
Is the advice useful?