Advice 1: How to make trees in the layout

The art of diorama military modeling and recreating a smaller scale picture of the fighting, well thought-out down to the last detail – is an exciting, complex and expensive Hobbies, which, however, creates spectacular paintings, admired as the owner and Creator, and other people. In the diorama to match reality not only important figures of soldiers and military equipment, but also environment – forest, field, relief, river or waterfall, and of course, trees and shrubs. How do the trees in the layouts, you'll learn from our article.
How to make trees in the layout
Instruction
1
To manufacture their own hands the layout of the birches in the scale 72 prepare some tools: hobby knife, flat stiff brush, a thin spatula and mini hand drill.
2
You will also need masking tape, superglue, putty for tiles, birch branch small size, dried moss, green powder, resembling the leaves of the tree (it can be made from crushed coloured paper or a tea infuser), black and white paint for models, the swamp green paint and matte varnish.
3
Sharpen a knife the tip of birch twigs. Wrap a twig with masking tape in several layers. The Foundation of the future trunk wrap more layers of tape to make the thickening.
4
Grout for tiles, diluted in a white paint, a twig handle wrapped with tape, using trowel or brush. The grout must be diluted evenly to the texture of the trunk did not spoil the lumps. Wait until the surface is dry to the future of birch.
5
Dip in black paint, a thin brush and apply black spots on the trunk of a birch. Greenish paint, spread and lightly color the base of the tree.
6
As birch branches, use the sprigs of moss to be painted with black paint. The most branched part of the branch paint and then sprinkle with a mixture simulating the fine leaves of the tree.
7
Prepare in this way a set of twigs. For installation manual mini-drill to drill the barrel holes under the branches, directing the drill at an angle from top to bottom. The upper branch are, in contrast to the lower and middle, fastened perpendicularly to the trunk.
8
The tip prepared by the branches drip a little glue and place it in the prepared hole. Do the same with the rest of the branches, holding each of the fingers in the desired position until the glue dries.
9
Thus, you will have the realistic birch in scale 72. Based on this method, you will be able to make any deciduous tree.

Advice 2 : How to make a tree model

Toys, created by your hands carry much more value than any other thing – especially when we are talking about detailed and beautiful layouts. Very often, the layout looks incomplete without trees and vegetation. Before its Creator, the question arises – how to make realistic models of different trees to place them inside of the layout. Use natural materials like sticks, bark, pine needles, and so on. In this article we will describe how to make several models of trees with his own hands.
How to make a tree model
Instruction
1
To glue the layout of a birch, take a strip of paper and twist it a flagellum. Obviate it with a thin wire and bend the ends, giving them the shape of the branches. Of green ivy or finely cut green paper to make leaves.
2
A narrow strip of birch bark glue spiral birch trunk and the branches paint with white paint. After the paint is dry, coat the branches with glue and sprinkle the prepared "leaves". This way you can make any deciduous tree.
3
To make the layout of the palm trees, take a long stick (30-35 cm), sharpened it at one end and causing a small transverse incisions. Remove from the old piece of wood bark and using a knife, peel off from the inner fibrous layer.
4
Cut or tear it into thin strips length of 3-4 cm. wide Take fresh pine shavings and cut them from a pattern of six large leaves, five medium leaves and five small leaves.
5
All the leaves color green paint. The small leaves attach brown thread at the top of the palm, and then start the circles to attach to the trunk of the remaining leaves, placing the largest in the lower tier.
6
Put the thread into the prepared notches in the barrel. Now wrap the trunk of the prepared pieces of bark. Install a palm tree on a stand, covered with glue and sprinkled with sand.
Is the advice useful?
Search