Advice 1: How to reprogram a SIM card

In our time, the presence of multiple SIM cards in a person is quite common, but to take along a few devices uncomfortable. The easiest option is to use an adapter for two SIM cards, but it can be used no more than two cards. Another option is to make multiseptate that supports up to 10 different rooms.
How to reprogram a SIM card
You will need
  • - programmer SIM cards;
  • - clean the SIM card;
  • - application for calculating KI and firmware.
Instruction
1
Insert the SIM card into the programmer, make sure you turn off the pin code request when switching on the phone. Then connect it to the computer for firmware sim card. Then start the application Woron_scan 1.09, select the type of device for the Card Reader, as well as Phoenix Card. Next, select the desired com port, then the frequency of the crystal oscillator.
2
To do this go to menu, Card Reader, Settings. To start scanning, return to the main menu, click Ki in the window that appears, click Start. If everything is set up correctly, then begin the determination process. By the time it can take from five minutes to a half hour, it all depends on the operator and the type of card.
3
Exit the program once the process is complete, the result is save in a file, open it using any text editor, find the value of Imsi and Ki of your card. These values will need to flash a new sim card.
4
Run the IOS SIM card. Use the application IC-Prog 1.05 D. the program folder and install the driver icprog.sys (http://download.siemens-club.org/files/sim-clone/icprog_driver.zip). Then right-click on the application file, select "Properties", go to the tab "Compatibility", then Windows 2000, then click OK.
5
Run the program Ic-prog, go to "Settings" – "Programmer". From the list select the device with the JDM Programmer. In the Port field select the com port to which the device is connected. In the option "Delay I/o", select the 30. Go to menu "Settings", select "Options". Go to the tab "Smart card", make sure the port value is correct. In the menu "Settings" select the check box next to Smartcart (Phoenix).
6
Restart the program. Then go to menu "File" open the file SIM_EMU_FL_6.01_ENG.hex. Put the programmer in Jdm mode - to do this, move the Sim Clock, Sim Reset, Sim data in the Program position.pic. Select the type of chip in the program.
7
Click "Program chip". Next, put the programmer in Phoenix mode, set the following in its provisions: clock Sim – 3,579, Sim reset High reset Sim data Sim reader. Press again the programming button.

Advice 2: How to insert a smart card

A smart card is used when connecting packages of digital television and is an integral part of the equipment which is used to receive a television signal. It is intended to decode encrypted channels and can be installed in TV, or in a separate signal receiver.
How to insert a smart card
You will need
  • adapter for the smart card;
  • set - top box with smart card support;
  • - TV with support for smart cards.
Instruction
1
To install the smart card into the TV uses a special slot, Common Interface (CI). To find this port, carefully examine the device or use its application. The slot is usually located on the back of the TV and can be signed as a PCMCIA Card Slot.
2
Depending on the connection type map is fixed directly or using a CAM-module, which often comes with a TV. Also CAM, you can sometimes give the company to which you are connected to digital TV services. Insert the card into the module so that its contact part was facing the slots on the module. Insert the card until it stops.
3
Install the module with the card in the slot of your TV in accordance with the marking applied to the device. For more accurate information you can use the instructions for use.
4
Depending on the TV model the installation of a smart card may vary. If you are installing the card in a separate console, is also necessary to place it in accordance with the directions of the arrows on the device itself.
5
Turn on the TV and the console (if available) to check availability of connected channels. If the installed card does not work, check the connection of the adapter again and if necessary again, remove the card from the slot and insert it back. If the channels were defined, but they are denied access, check the card or contact the helpdesk of your service provider. It is possible that you have not activated you need a set of channels or payment for the use of television.
Note
To install the smart card is only in accordance with the instructions of the TV or console. Incorrect configuration and installation of equipment may cause damage to the TV or the appearance of damage on the adapter itself.
Is the advice useful?
Search