Advice 1: How to glue a magnet

When there is a desire to decorate the magnetic Board or the refrigerator door, always remember indispensable magnets. How much warmth and tenderness that made by hand. If you have a billet, a favorite photo, or a creative poster for decoration, it is the case for small - to glue the magnet.
How to glue a magnet
You will need
  • magnet
  • glue "Moment universal"
  • - sandpaper or nail file (grit 80)
  • - double sided tape
  • - alcohol, acetone or solvent
  • - cotton
Instruction
1
Carefully prepare the surface to which it is necessary to glue the magnet. If it's plaster (stucco), remove all burrs and protruding indent. Do this with fine sandpaper (emery paper) or nail files for artificial nails (grit 80). Move in one direction only – when driving back the plaster may crack. When the magnet is required to stick to the wood or plastic, clean the surface. Apply a small amount of alcohol / acetone / thinner on a cotton pad and wipe them with the necessary place. Allow to dry yourself. Do the same thing with a magnet (if you glue it on the glue).
2
When the magnet is required to stick to the wood or plastic, clean the surface. Apply a small amount of alcohol / acetone / thinner on a cotton pad and wipe them with the necessary place. Allow to dry yourself. Do the same thing with a magnet (if you glue it on the glue).
3
To stick self-adhesive magnet, cut a piece the required length. Remember that in this type of bonding, the product must be very easy. For example, a small magnet on the fridge or a photograph. Remove the protective film from the magnetic strip, then press it into prepared on the product site. Hold it for a few seconds.
4
Thin magnetic tape is also designed for bonding to a light flat products. It has no adhesive layer, so depending on needs you can use either double sided tape or glue. If you chose the glue, apply a thin stripe with a wavy line from the beginning to the end of the magnet. Do not apply directly to the product, hold the air for 10-15 seconds. Strongly press in to the prepared place. Wait another 20-30 seconds. Do not use the product immediately, it is better the next day.
5
For heavy items made of wood or plastic using conventional magnets. They can be different thicknesses and shapes. To glue such a magnet, clean the surface from dust, grease and dirt. Apply a DAB of glue both on the surface of the magnet. If you just allocated a place on the product, you can put some glue on it.
6
Do not apply immediately, allow the glue a bit to get to grips with the surface for 15 seconds. Attach the magnet to the product, strongly press. Hold as 30 seconds. If the product is not fragile, then put on top of the day something heavy for best results fixing. After a time carefully lift the press, check the firmness of the magnet.
Useful advice
In order to avoid ugly stains from glue better to use "universal Time transparent."

Advice 2: How to stick edging tape

Edging tape is designed for pasting the ends of furniture made of particle Board. It increases their strength, protecting from moisture and preventing evaporation of the impregnation. It can be applied to the restoration of such furniture. To cope with this material is capable of even a novice carpenter. It is often made of decorative paper, which is impregnated with special resins.
How to stick edging tape
You will need
  • - edging tape;
  • - detail of particle Board:
  • - a sharp knife;
  • - scissors:
  • Board;
  • - abrasive sponge;
  • round screwdriver;
  • metal long ruler;
  • - iron.
Instruction
1
Select edge bandings. It is of various widths. Pick one that matches not only in color but also in thickness of the part. Usually its width is from 1.8 to 4.5 cm Strip may be slightly wider than the surface you intend to cover, but not much.
2
Clean the edge of the plywood. Remove the dust from it. Start with the end which will be less noticeable. It is necessary to hide the joints of tapes. The pasted over surface should not have significant irregularities. Of course, the tape of them will be cut out, but large bumps and notches better to remove.
3
Carefully inspect the ribbon. It should not be joints, which are formed by connecting the individual strips in the roll. Usually these joints are invisible. However, they can greatly damage the appearance of the product, if you are going on the tape, to apply any coating.
4
Measure the length and width of the pasted over surface. Take the tape around 0.3 cm wider end and approximately 2.5 mm long. It is easier to do with a ballpoint pen on the iron range. Trim the ribbon is also better on the line with a sharp knife, like a Shoe. The blade must be sharpened. However, it is possible and to cut with scissors.
5
Regulator of iron supply on the division of the "cotton" and allow it to heat up. First, glue the rounded corners. Determine the midline of the face, it can even draw throughout. Find the center edge and apply it to the end of the part, aligning the middle lines. Slowly iron the first one half of the tape, and then another. Need to press hard enough to make the adhesive layer is melted, and the tape lay on the rounded corner smoothly and without wrinkles. Pay special attention to the edges. If they press enough, the tape will break away from the details. While the glue is hot, apply the coating using a round screwdriver or other similar tool.
6
Allow the glue to cool for ten minutes. Then re-heat the iron and smooth the tape to the edges of the upper and lower surfaces of the part. The iron thus it is better to put at an angle to the line of coupling was more subtle. Press the iron hard, but not dramatically. After the glue has cooled down again, remove the excess tape. For cutting the edging strip at a right angle there are special tools but you can do enough with a sharp knife. Before you cut the extra edge pieces, don't forget to look at the direction of the fibers of the workpiece. If they are aimed down, a better cut from right to left, and if up — on the contrary.
7
Abrade the surface of the plywood along the edges of the edging strip. Remove all irregularities. Hold the sponge directly against the corners of the part. Instead of a sponge you can use a piece of sandpaper with Velcro attached to the bar.

Advice 3: How to glue a mirror on the door for wardrobes

Modern design ideas often include the presence of mirrors in the design of any room. Mirror paintings cover not only the column and wall panel and door furniture, including wardrobes. One of the most common ways to install the mirrors is installation with glue.
How to glue a mirror on the door for wardrobes
You will need
  • - mirror sheet;
  • - the glass cutter;
  • needle;
  • - Hairdryer
  • water;
  • - Mel;
  • - adhesive sealant;
  • tape of foamed polyurethane.
Instruction
1
Pick up the mirror of such thickness that it does not become an obstacle to the movement of the doors in the grooves of the wardrobe. If you purchased the mirror sheet does not have a machined edge, or the shape and the area is more area under the mirror on the door make it pruning. For this, first of all, remove the measurements from the Cabinet door.
2
Carefully place the mirror on a flat surface. The amalgam should be on top. Drag on the canvas size. On the cut wet amalgam with a solution of vinegar or plain water. Apply the rule, and swipe along the edges with chalk. Then take the needle and accurately on the cutting line to cut through the amalgam.
3
Flip the mirror sheet and glass cutter draw a line symmetric to the line of cut done by the amalgam. The metal part of the glass cutter tap line. When the chip will become noticeable, a bummer the excess glass. The amalgam dry with a Hairdryer.
4
Remove and place the Cabinet door so that it adopted a strictly horizontal position. Remove surface dust and any dirt. As rags, use only those materials that do not leave fibers. If to clean the surface of dirt had to use clean solvents, be sure to let them fully evaporate before applying adhesive.
5
Use for mounting mirror reliable, not destructive amalgam, polyurethane adhesive sealant and double-sided tape on the foam plastic basis. First, apply the tape, positioning it so that when the doors to the place she was in a vertical position. Evenly distribute over the surface of the strips of tape, each of which shall be not less than 10 cm in length. After applying, press the tape to the surface without removing this protective soy.
6
The adhesive sealant also apply vertical strips, the number of which depends on the thickness and area of glass cloth. The diameter of the strip, which is regulated by cutting the plastic tip of the cartridge should be about 6 mm. Apply strips not more than 10 cm from the edges of the mirror and within 5 cm from the glued strip.
7
Start sticker mirror glass. Clear coated Cabinet door tape protective layer. Put a mirror on the door and press to evenly distribute the adhesive and achieve a reliable contact with the fabric surface of the tape.
8
Leave glued the mirror in a horizontal position for 24 hours until full curing of the sealant. The temperature should be not below 20 degrees.
Search
Is the advice useful?