Advice 1: How to improve DSP

Despite the variety of modern materials in the furniture industry, case products from particleboard (chipboard) are not losing their popularity. They are available to the mass consumer, and with proper treatment products and the good care can last a long time. But no matter how you care of your favorite cabinets and tables, sooner or later they will need repairs. At a certain skill home master can Refine chipboard and completely transform old furniture.
How to improve DSP
You will need
  • - sandpaper;
  • - wash the old paint.
  • water;
  • soap;
  • - rags;
  • - primer;
  • - putty;
  • - spatula;
  • construction Hairdryer (iron);
  • - velour roller;
  • - grater or bar for grinding;
  • spray gun for paint;
  • - paint;
  • - Lac;
  • - furniture edge (or edge glue);
  • set painting for the old days (different paint colors, a brush, stain, varnish).
Instruction
1
Repaint the facades of chipboard is an easy way to update furniture to give it an interesting design. To ensure that the product does not look homemade, it is necessary to carefully perform all stages of finishing works. To begin, prepare the surface for decorating.
2
Scrape the old paint layer from the plate with emery or a special chemical paint removers. Once done, rinse the furniture with warm soapy water and dry.
3
Pick up in store construction materials primer that increases the adhesion of the treated particleboard with new decorative layers. It is recommended to use a universal acrylic primer ("Primer Primer") – it is well suited for all complex surfaces of wood. Evenly distribute the soil on the cleaned plate can be a velour roller.
4
Fill all cracks, the furniture was perfectly smooth. To do this, buy a composition suitable for the treatment of it chipboards. Usually putty is sold ready to eat, you will only need to follow the manufacturer's instructions. The leveled surface of sand with a special grater or a bar.
5
Paint the chipboard out of the sprayer in two coats, allow paint to dry and apply another couple of layers of clear protective varnish.
6
As necessary, update the edges of furniture facades from a particleboard. Before processing they must also be clear, align and zashpatlevat. After this is possible bygluing to the ends of the finished melamine or polyvinyl chloride (PVC) edge. Pick up at the furniture store the material suitable tone. Heat plate construction dryer or simply an iron, then press them tight to the ends and iron.
7
Another option is a furniture slip edging of PVC, which can be worn on the edges of countertops and cabinets overlap. For better fixation of the plant material on the glue.
8
To Refine DSP can also use a variety of fashionable designs, such as artificial aging. To give furniture a "flying time" to do it tastefully and not ruin the material, from the master will require special diligence and good taste. One of the easiest ways of such decoration is the use of inks of two colors.
9
Cover chipboard with wood stain, then a darker color tone. Do the brush rubbing, chaotic traffic. Then dip it in lighter paint and put the second layer of the stroke. It will give old furniture an interesting texture. Noble stylized "retro" lacquer.
10
Try more complex and creative ways to redo old furniture from chipboard. Plate can be dismantled, to cut Windows and decorate with stained glass or braiding from willow vines. To work with old cheap particle Board is a good school for an aspiring furniture maker and interior designer.
Useful advice
If the experience in upgrading old furniture will not succeed, contact furniture company with the service to replace the worn fronts and worktops. Is the ability to "disguise" the body of the product at an affordable price.

Advice 2: How to paint particle Board wardrobe

To protect and improve the decorative properties of products made from particleboard, they should be covered with waterproof varnish or polymeric films. How to paint the Cabinetto return to it original form?
How to paint particle Board wardrobe
You will need
  • fine - grain sandpaper;
  • plaster on wood;
  • - primer;
  • - Lac;
  • - masking tape on a paper basis;
  • - a brush or roller.
Instruction
1
These wardrobeyou can cover with paint or varnish. The Polish refines the appearance. Before painting it is important to carry out preparatory work.
2
Using coarse sandpaper, remove the old layer of paint or varnish. Carefully where you want to locate the surface as much as possible to get rid of the bumps. Remove dust and dirt.
3
Fill cracks and chips. To do this, apply putty to create a smooth surface. Possible swipe the entire surface with putty Cabinetand in two steps. Let the first layer dry thoroughly, as there can be shrinkage. Apply a second coat of putty.
4
Proceed to the responsible process – grinding. Use fine sandpaper. The result is a completely smooth surface. Remove any dust left after sanding.
5
Not less important stage of preparation – primer. It will provide a beautiful Shine and smooth as possible the surface color of the wardrobe. To Prime the can with a brush and roller. Apply the first thin layer. Wait for final drying.
6
After finishing the preparatory works start painting the wardrobe. Typically, the paint or varnish on the chipboard is applied in 2 layers. If you notice errors on the surface, then clean with fine sandpaper.
7
When painting the individual parts of the surface, use masking tape. It will help to prevent sagging and the appearance of jagged edges. Do not use in this paper another Scotch. It can stick pieces of paint.
8
For the final drying to leave the wardrobe for about a week. That's enough time to nail is firmly attached to the surface.
9
When painting you can use various stencils, which will be interesting designs and patterns on the surface of the wardrobe.
10
If your wardrobeand damaged ends, protect them with veneer. To do this, enough with the hot iron to glue the plastic tape with an adhesive coating.

Advice 3: How to improve furnace

Folded oven need additional decoration – it has a rough side with traces of the solution and not a very attractive look. But it needs to be integrated with the interior of the room. To elevate the furnace, it is necessary to consider the methods of finishing various materials and choose the one that suits you.
How to improve furnace
You will need
  • - brick kiln;
  • - clay;
  • - lime;
  • asbestos;
  • - salt;
  • - blue;
  • - trowel;
  • - hammer-kirochka;
  • - jointing;
  • - the range;
  • brush;
  • - rags.
Instruction
1
Select the method of finishing

To give the furnace a majestic species, there are several ways: a veneer of glazed tiles, tiles, majolica, or the confinement in a metal box. Undeniably, finishing such an expensive material will give the building elegant look and will decorate the room. But you can elevate the furnace is simple and accessible means: perform jointing or plaster surface. The first involves smooth brickwork and decorative stitches. The second outdated, but common technique, not requiring special skills and substantial costs.
2
Prepare the surface

Clean the bricks from the remnants of dried clay. Inspect existing chips – they need to pay more attention when decorating. For better adhesion of plaster and brick will clear away seams on depth not less than 5 mm, remove the crumbs from all the holes and sweep up dust.
3
Prepare plaster mix

Mix the clay, sand, and asbestos in the ratio 1:2:0,1. Each component of the pre-sift through a sieve. Dilute each with water to the consistency of sour cream and get to work, starting at the top of the furnace.
4
Stukatura oven

Moisten the walls with water and put on her first layer (3 mm) plaster. Each subsequent layer is applied after drying the previous one - its thickness at the end of the finish should be 6-8 mm. the Exception will be where there was a chipped brick and irregularities – are permissible 10-12 mm. After work let it dry and then lightly heat the oven, heating it up to 35-40 degrees. If, after this, it formed cracks, moisten them with water and zarovnaya defects.
5
Whiten oven

The final stage of finishing is the whitewashing of the furnace. Below the surface is not soiled clothes, prepare the mortar with the salt. Extinguish the lime water or skimmed milk and add table salt (100 g per 10 liters). To make the surface of a special white whitewash add in a few drops diluted in water blue.
6
To blend oven another way

Do the jointing. Pick up a smooth brick kiln without any chipping at the edges and carefully lay the stove. Start the process of pointing to the drying of the solution. After several rows of masonry will seal the joints between the bricks using a special tool. Leaving gaps unfilled by 10-12 mm, you will get a relief surface with a clear pattern of masonry. Wipe off excess grout and Polish oven side bricks. Then sweep up with the brush dust and wipe with a dry cloth. Prepare for the selection of decorative stitches mix, which mix white or orange cement with asbestos powder. RUB it first in a vertical and then horizontal seams. If you like contrasting combinations, underline unravel solution of black clay and fine moulding sand.
Note
To not cracks, carry out plastering works after the complete drying of masonry and precipitation of the furnace.
Useful advice
To avoid delamination of the finish when heated, the furnace can be used to apply plaster in a thin metal mesh with a cross section of cells 10x10 mm. Apply it before starting work on the masonry, securing the wire between the rows of bricks. Below the grid was not visible, the thickness of the plaster layer should be at least 10-15 mm.

Advice 4: How to cut laminated particle Board

For the manufacture of furniture in a home workshop is often used laminated chipboard. Being made of coniferous and deciduous trees, chipboard possesses the essential qualities, including durability and ease in handling. The main drawback of MDF is that careless pruning possible chipped material. To correctly cut chipboard, you should follow some rules.
How to cut laminated particle Board
You will need
  • - tape or measuring ruler;
  • pencil;
  • - hacksaw with fine teeth;
  • - jigsaw;
  • - circular saw;
  • - masking tape or Scotch tape.
Instruction
1
Select the type of cut you want to use when processing laminated chipboard. A straight cut is used for cutting rectangular shapes used in furniture manufacturing. Some details of designer furniture, require a curved cutting. Possible and mixed way to cut chipboard.
2
Prepare the necessary for cutting chipboard tools. You will need a saw with small teeth or jigsaw. For cutting you can also use a circular saw if the teeth of the blade are of a suitable size. To protect the laminate from damage when cutting material, prepare masking tape or Scotch tape. For marking workpieces necessary ruler and well-sharpened pencil.
3
Mark on the sheet in accordance with the requirements of the finished product. Mark with a pencil or marker with the ends of the plate the point of the intended cut.
4
To protect slabs from chips stick to the cutting masking tape, Scotch tape or other tape with adhesive layer. Laminated particleboard is coated with melamine foil and varnish, which is applied at high temperature and pressure. The tape will protect the edges of the cut from scuffing and chipping.
5
After a label of masking tape connect the pencil point of the first marking.
6
Getting cut off, LDSP, hold the hacksaw at an acute angle to the plate surface, to make the edges more smooth. Do not try to push hard on the tool, the movement should be rhythmic and light.
7
If after cutting edge is smooth, the product requires no additional processing of the edges. Upon detection of irregularities treat them with a file or rasp. The ends of the plates, which was the result of the cut, paste over with an interline interval under colour of the plate surface to make the whole product additional protection and attractive appearance.
Search
Is the advice useful?