You will need
- - iron
- - gauze or cotton fabric;
- - water.
In order to put in order desiccated polyester, use an iron with a regulator. Among modern irons are very difficult to find such on which it is impossible to set the desired temperature. But as the old primitive irons almost never go down, it is likely that he has you, and even household uses. Antique iron suitable in this case, but not very comfortable.
Dip the product in a basin of cold water. Give him a little dry. Remember that polyester dries very quickly. The cloth should be slightly damp. If a thing is relatively new, you could be the cloth that it came with. Such patches makes sense to keep because they can conduct experiments without fear of damage to the garment. In this case, you need to experiment a bit with the temperature of the iron. It should be a little higher than the one at which you usually iron the clothes made of synthetic fabrics.
For wrinkled polyester set it to the same temperature as that for silk. In this position, the iron can be completely relaxed without fear that the fabric will melt. However, at this temperature, the folds may not be smooth. Slightly turn the knob. Try to iron the cloth. If not, then iron some inconspicuous place on the product. This can be, for example, the binder, the inner part of the cuff or hem fold-over collar. As a rule, pleats at slightly higher than normal temperature perfectly smooth. Iron through a thin cloth, like gauze.
The need to iron the product can occur and in that case, if you want to look especially elegant. For example, you are going to the ball. Perfectly ironed clothes not only looks good but also creates a mood. No special tricks need not apply. Put the controller in the mode "silk" and iron the product through a layer of gauze.
If still in your possession was an antique iron, and iron have grandma's way. Heat the iron and Try it on scrap and turn it off. It cools very quickly, so the product from synthetics you ironed in time. Ironed it on the front side with a cotton cloth.
Advice 2: How to iron silk
Silk is an excellent material from which sew both clothing and accessories (e.g., scarves). Bed linen made of natural silk is considered a luxury item and gives pleasure. This material is perfect for warm weather, not warm as the body heat and quickly evaporates moisture from the surface of the skin. To care for silk must be very sensitive and touch should be only in special conditions.
High-quality silk is almost not wrinkled. So scarves and tops can not be ironed at all. But skirts and dresses from this material quickly crumple, so they have to podgadyvat. And it should be done properly and carefully.
To iron silk products better when they are still slightly damp after washing. The fact that in the case of dripping of water or powerful jets of steam on the silk fabric, stains and divorces. Why moisten clothes during Ironing is not recommended.
It is undesirable to iron silk clothes with steam. Hot steam can warp the fabric under its influence may also change the color of the product.
The iron should be pre-heat by putting on the minimum temperature. On modern devices there is a special mode of "silk". If you are not confident in choosing the right temperature, you need to try to hold the iron in inconspicuous place, such as in the bottom corner of the product. If it does deform, the defect is not so noticeable.
Iron products made of silk have on the reverse side. If you remove the clothes it is impossible or complicated cut does not allow you to iron the fabric on the inside, contact a gauze or soft cotton thin fabric. Put cheesecloth on top of the product, smooth to folds, and gently iron.
Seams on clothes during Ironing can Shine if you do not obey all requirements. To return the garments original appearance, should be re-wet it completely, dry under natural conditions and then ironed at a lower temperature.
Special care requires the so-called "wild silk" – Toussaint, the fibers of which are intertwined a little differently than usual. To iron this material needs a dry and necessarily from the wrong side.
Advice 3: How to iron shirt sleeves
Shirt is the kind of dress that looks elegant and very useful. To look presentable shirts should be ironed. Sleeve same is most clearly evident with their "arrows".
You will need
- an Ironing Board;
- - iron
- - shirt.
Set up your work space. Check that the Ironing Board was smooth and without deformation.
Select the shirt, the sleeves of which will be ironed. Remember that the fabric from which to sew a shirt, plays a very important role in the process of Ironing. If the clothes are made from cotton, then heat the iron up to 150 degrees, if the shirt is linen, warm to 220 degrees, and if from the polyester, up to a maximum of 110 degrees. Also a cotton shirt and polyester to stroke a lot easier than from flax.
Check the condition of the fabric of the sleeveless shirt. If the fabric is dry, iron it will be difficult. In this case, just spray the sleeve with water or use steam on top of the handle of the iron.
Start smoothing sleeveless shirt. First, slide the iron on the inner side of the cuffs. Flip the shirt and iron the outside cuff. Please note that the fabric on the cuffs is more dense, so one stroking is not enough. If the sleeves are made for cufflinks, then iron the cuffs unfolded, and then fold and once again walk the iron from the front side.
For Ironing the main part of the sleeves take a special small Ironing Board. Put the sleeve on the Board in turns then outer, then inner side. Thus, paving one way you don't mash the second.
If the special Ironing Board is missing, put the sleeve on the surface of a Board, seam up. Iron, do not pull the fabric strongly, so she stretched and looked deformed. Now flip the sleeve so that the seam was on the side. Again iron. Very good smooth upper bound sleeves. It will be "arrows". Place the sleeve of shirt cuff buttoned up. Do the final run with an iron, well carefully between the buttons.
When Ironing the front side on dark fabrics can stay shiny strip, but if you need to iron the shirt with the front side, then use steam, lightly touching the product with iron. In addition, the back should be ironed and shirts of shiny fabrics, so they are not faded.
First give more detail with less area. Try to iron along equity lines, to avoid stretching the fabric. The first thing ironed collar, with stand