Advice 1: How to adjust the modulator

The change in media is happening at a rapid pace. For the motorist it is very important to music in the car. But the old unit only supports CD's that go out of fashion and less and less updated. In addition, the radio drives tend to jump on the sound track while riding over bumps. A good solution for motorists is a FMmodulatorthat can play music from a FLASH drive.
How to adjust the modulator
Instruction
1
To configure the modulatorand look at your free radio frequency. To do this go to the radio mode. Use the frequency on which no radio. Consider also local radio stations.
2
Install FM modulator in the plug for the car cigarette lighter. After that, it will turn on. In a pinch, use the remote control to turn on. With the buttons "Forward" and "Back" on the body of the modulatorand or the remote control to tune to the frequency that was selected on the radio.
3
Insert the memory stick into the hole for the FLASH drives. After a short amount of time the modulator will transmit a signal on the radio. If frequency is configured correctly, the music that is recorded on the FLASH drive will be played.
4
Some FM modulator, you have functions to set up the sound. To do this, use the remote control, use the corresponding buttons. You can also adjust the playback queue of audio tracks.

Advice 2: How to burn a disc for radio

At the time, the radio in the car was a symbol of status and luxury. Today, those models of stereos, whom I admired and dreamed of are outdated on the background of a full car media players. But not all people are running after the technical progress. A quite pleased and CDs, because often need to burn the disc for audio.
How to burn a disc for radio
Instruction
1
To burn a disc for radio, which it will, look online to find user guide for your player. Or, if it is preserved you from the time of purchase, then use them. Find the information about the playback formats that are supported by your radio. The most frequent and common formats that are played by a receiver:

• WAV;

• CDA;

• MP3.

The CDA format is a regular music CD. Two other format require a specific decoders for playback.
2
To burn a disc, download and install the computer program for recording CDs. Similar programs there are many: Astonsoft DeepBurner, Ashampoo Burning Studio, Free Easy CD DVD Burner Small CD-Writer CDBurnerXP, Nero, and others. Further steps we will describe on the example program from Ashampoo.
3
Insert into CD-R or CD-RW disk and run the program to burn discs. In the left part of the window there is an option "Record music", clicking on which you'll see a list of commands, such as "Create Audio CD" and "Create MP3 disc". You can use these opportunities and to record a disc for audio from all audio tracks of different formats that are on the hard drive of your computer. Program Burning Studio itself encodes them into MP3 format, you are asked to specify the quality of encoding. However, the recoded music will take some time, and the resulting sound may not be very clean. With the exception of options when your radio only supports the Audio CD format. In this case, choose the appropriate command in the menu.
4
Easier to burn a disc for audio via the submenu "Burn files and folders" - "to Record a new album". In this case, just add MP3 and WAV files in the recording list and follow the instructions on the screen. Radio successfully reproduce thus recorded disk.
Note
Windows 7 how to burn a CD/DVD-ROM, CD-ROM or DVD-ROM drive in Windows Explorer 7. – from the context menu select send to –> DVD RW drive (backwad:); – in the window to Burn the disc – Like plan to use the disk? set the desired switch – off As USB flash drive (default) or CD/DVD player
Useful advice
On them with a laser, the recording and reading of information. Many people mistakenly believe, that the DVD discs can record only cartoons and feature films, and CD drives — everything else: text documents, photos, music. Now very popular is the sale of license films on DVD. Documents, music, photos and other files, it is possible to record both to DVD and CD.

Advice 3: How to configure sound in the car

It is not enough just to buy and put in a car audio system, even if it is high quality and expensive. Depending on the system the sound will be more or less quality, but without the settings of the sound potential to be unsolved. To complete settings pre-out, does the audio from the radio or from separate amplifiers, without processor.
How to configure sound in the car
Instruction
1
If the sound is issued by radio without amplifiers, adjust it as follows. Put the music that you like, and set the level of soundand on the border of the beginning interference ("wheezing"). That is, so that the slightest increase in volume started "wheezing". Slowly start pulling the upper and lower frequencies. Top set to your liking, and the lower set on high, on the border of the beginning of the "gap" speakers.
2
Adjust the fader and balance audio system. For this study, using the user menu adjustments. Rear components (columns) configure only podsvechivaya background. The main music should come from the front speakers. To adjust the level of the front and rear speakers fader designed. They adjust the components so that the level of soundand the front was more the rear at 15%.
3
In the presence of component speakers, set the crossovers to the sound of tweeters on the magnitude of 2 DB. And exactly the same as in paragraph 2 remove the main sound on the front speakers. When setting up a soundand right/left speakers, use the balance adjustment. And install the balance of the right components at 10-15% more than on the left, some softening of the latter.
4
If the audio system usnascheny of the power amplifier, optionally, set up the filters and adjust the power level of the amplifier. Please agree on the level of the signal receiver to the signal level of the amplifier.
5
To do this, reset all settings, setting them to zero or to factory settings. The power level of the amplifier turn on minimum sensitivity. Start to increase the volume of the receiver to the starting point of the distortion sound. As soon as they start, maintain your level. Get to the amplifier (usually it is in the trunk) and gradually increase the power level until a distortion sound. As soon as they appear, reduce the power.
6
Locate the amplifier filters the upper (high pass) and low frequencies (low pass). High-pass filter set to 80-100 Hz. The low – pass filter to the level of 70-90 Hz. Experiment with the filter settings to soundlike the picture was more accurate. Then adjust the fader and balance the ratio of the level of soundas front/rear and right/left speakers as described above.
Note
Every new acoustics is the period of "running in", which lasts 1-1,5 months after the start of its operation. During this period, avoid to turn on the sound at full capacity. If the system includes subwoofers increase this period to 2 months. Thereafter, the power amplifier reconfigure again.
Useful advice
With all the adjustments, try to make it so that when playing music you did not create the feeling that all the sound comes from the windshield of a car. Must be the feeling that the sound is coming from the speakers.

Advice 4: How to make a fm modulator

Car fm modulator is a decoding device that is able to convert and stream music from a memory card or USB flash drive. In most cases, a fm modulator, you have given the range of variable frequencies, although there are models with fixed transmitters on a frequency band of broadcasting.
How to make a fm modulator
You will need
  • - fm modulator;
  • - a pair of computer speakers;
  • - computer cords;
  • knife;
  • - fuse;
  • - soldering iron;
  • - screwdriver;
  • - the file;
  • - power supply unit;
  • - wire;
  • - duct tape.
Instruction
1
Correctly set the fm modulator is simple: insert the transmitter into the lighter socket. Then put on a modulatore frequency.
2
Finally, set the stereo to put on a modulatore frequency and enjoy listening to music.
3
Of the fm modulatorand you can make a great MP3 USB player, with radio you do not need. The first thing to remove from the panel ashtray: this place will be the speakers.
4
Cut the plug from the computer cord in the hole through which the stretched walking out of the cabin to the bonnet wire, thread the cord.
5
Connect the cord to the battery. In the end it should look like this: one end of the cord should be attached to the cigarette lighter, and the second to the battery (it is desirable that the connection was made using the fuse).
6
Disassemble the column. Speakers install in the hole from under the ashtray and solder to them wires (you can use even those wires that used to connect speakers to the computer). In the end, if you did everything correctly, it should be equipped with two speakers, from which hangs a wire with a jack.
7
Disassemble the lighter and with a file make a notch under the wire. Then straighten the "whiskers" in the nest.
8
Solder the wire to the body of the cigarette lighter, then the body gently wrap with electrical tape.
9
Then carefully grind the teeth of the outer cylinder (the body of the cigarette lighter) and wrap and this region several layers of duct tape: generally there should be no contact with the outside zero.
10
Disassemble the old power supply: you need the inner part. Taken from the power supply "filling" will act as a filter that protects the device from interference which may be caused, for example, the operation of the generator. The filter will consist of coil, capacitor and connecting terminals.
11
To the input of the amplifier solder the wire with the mini jack: this will give the possibility to connect to an amplifier fm modulator. Then in the nest the modulatorand make using a conventional wire jumper wire: this is necessary in order to soviani the minijack was used for the signal transmission and not reception.
12
Place under a panel, an amplifier and a filter, and then connect all the wires (for power supply with lighter socket and power) colors, that is, the pros to the pros and cons by cons.
13
Connect the speakers to the amplifier and posledni connect to fm modulator (all connecting wires hide under the panel).
14
Then turn on the amplifier, plug in fm modulator USB flash drive with the songs and hit play: the excellent music you provided.
Note
Using a soldering iron, observe the safety regulations!
Useful advice
Functionally distinguish between fm modulators with internal memory, the mode of operation from the built-in device battery life, can play video files as well as with a Bluetooth option.
Is the advice useful?
Search