Advice 1: How to adjust the door

Not always the case that the door is properly installed. Sometimes appear minor faults, which are usually the result of poor installation of the door. And even new, qualitatively installed doors sometimes need adjustment. Consider the process of adjustment of the plastic doors, including the balcony. Elements of the hardware on the doors from different manufacturers will vary slightly from each other. But it regulates all plastic doors in General the same.
Well adjusted the door will last longer
Instruction
1
To adjust the door, you need Allen keys for two and a half, three, four and five mm. you should Also get a cross screwdriver and flat, just in case.
2
To adjust the door at any time: a long time after the installation of the door (when it is already worn out) or almost immediately after its installation. If the door is not yet installed, do it. On each side of it should be at least four mounting points. The door is "raw" will probably not work quite as you would like. Configure the circulation of the doors with screws located in the door hinges. Such screws are usually three pieces.
3
To get to the adjusting screws it is possible only by removing the pre-protective decorative cover. Open this door wide open, and on the other side of the hinge hexagon socket 3 mm, loosen the locking screw. Close the door and remove the covers. Beneath them among other things, you will see a long screw positioned horizontally. With this screw the door is adjusted horizontally.
4
Tightening the screws the two top loops, you can lift the edge of your door. Adjustment of all three loops will allow you to move the door left and right. Sometimes it is necessary to lift the door leaf for a short distance. For this purpose, there is a screw hiding in the bottom of the loop and adjustable hexagon socket 5 mm.
5
Upper and lower door strikers adjustable with hexagon 2.5 mm or flat screwdriver (in another version). Phillips screwdriver adjustable strap main gate, which is located in the middle.

Advice 2 : How to adjust interior door

Almost any problems associated with connecting door, for example, a squealing noise, difficulty opening or closing, can be eliminated by adjustment. If the door you put the master of the shop and gave a guarantee, it is better to call them up again and just watch the process. Otherwise, try to adjust the door yourself.
How to adjust interior door
You will need
  • — screwdriver;
  • — based lubricant grease or pencil lead;
  • — plane;
  • — hammer;
  • — chisel;
  • — a plumb or a laser rangefinder.
Instruction
1
If the door does not close, check the correct installation of the box by means of a plumb and a laser rangefinder. Maybe during installation there was a bias. In this case, remove the box from the doorway and install it again, when you do this, screw in each joint at least two screws.
2
Note, the door also may not close due to the fact that loops are planted too deep from the outer face plane of the door. To fix this, disassemble the hinges and fix them again, shifting closer.
3
Maybe the door doesn't close properly due to the fact that the hinges are recessed enough into the box and protrude above the surface. In this case, Unscrew the screws holding the hinges, and increase the depth of the grooves.
4
If the door is "bogged down" in the box and clinging, the cause may be too close to the mounting of hinges to the edge of view, not a "peep" if the loop over the front of the plane. Fix it by re-fastening.
5
Quite possibly, cause a loose shutter doors is that the grooves for the hinges were too deeply cut. In this case, put inside the strip of cardboard.
6
If the housing of the latch or lock door handles clings to the pad on the receiving side and projecting over the end surface of the door, correct this defect by increasing the depth of the groove under the lock or latch.
7
If the door slightly touches the upper or lower joint, put in place of the alleged contact of the copy paper and close the door. Then see where a spot appears. Small bumps on the wood frame you can simply "crush" with a hammer. This was to deal with the problem failed, stelite extra plane and paint the door again.
8
To get rid of squeaky doors off the hinges, and then lubricate any hinges with grease based grease or put inside a small piece of graphite slate pencil and hang back.

Advice 3 : How to handle Chinese door

Chinese doors are very popular. They are considered the best choice for those who are not going to pay for the goods. And although many Chinese products associated with "consumer goods", do not succumb to the majority opinion, because the availability of metal Chinese door did not say on neschopnosti this product. Besides, the Chinese installed the door and easy to adjust.
How to handle Chinese door
You will need
  • lubricant;
  • - rubber seals;
  • tools.
Instruction
1
Carefully inspect the installed Chinese metal door and try to figure out the reason why you hear the squeaks, and to determine the place where they are going. In most cases, the creaking hinges of the door or the sound caused by friction of metal of a door cloth on a box.
2
If the creak comes from the door hinges, lubricate them. This will enable you to avoid the inconveniences caused by unregulated Chinese doors.
3
Another reason, which might squeak door hinges - hinges hit the dust. The reason for this can be very diverse, for example, the apartment is undergoing renovations (and as you know, during the repair of the dust and dirt galore). Purge the inner loop, and then lubricate them with special grease.
4
If the input Chinese doors miss the draughts, cold and noise, then you need to take care of the noise for such a door design. In this case you may need the rubber seals, and complete the insulation of the front door.
5
Chinese adjustment of the inlet door is performed in the following sequence: loosen the middle hinge, then follow the weakening of the lower or upper hinge (the choice of loop depends on the place, whence came the creak). Painting metal door pull or move to the box, tightening the nuts located at the extreme loops.
6
Following this posetite door: this must be done in order that the nut had taken their seats. Then open the front door and close it down with a pen and listening, whether there is abnormal noise or squeak. If you cannot resolve the problem, repeat all the operations related to the setup of the Chinese door again.
Note
Follow safety precautions as there is a chance to squeeze the fingers.
Useful advice
If you are not able to adjust the front door with your hands, use a qualified technician for whom this task will not cause problems.
Is the advice useful?
Search