Advice 1: How to adjust Cabinet door

The most common reason that the door of your closet sagged and ceased to function properly, is a weakening of the hinges. To adjust Cabinet doors it is possible yourself using a minimal set of tools.
How to adjust Cabinet door
You will need
  • - Phillips screwdriver;
  • glue;
  • - matches;
  • door leveler;
  • - hammer;
  • pencil;
  • - the range;
  • - the drill.
Instruction
1
Open the Cabinet and inspect the hinges. As a rule, doors wardrobes and kitchen cabinets are fixed on the Cup hinges. One side of the loop is set in a special hole on the inside of the door, and the second is fixed on the sidewall, on the inner side. This construction allows to correct the distortions and to adjust the closing mechanism.
2
Check the tightness of the four mounting screws, which are fixed to the Cabinet door. If they are loose, tighten them. To do this, take a match and make them wooden plugs of appropriate size. Remove the screws. Gently RUB the cork with glue and insert in the mounting hole. Install and tighten the bolts.
3
To adjust the distance between the closed closet door and the front edge of its wall can by loosening the screw located on the far side of the loop, and gently pull the door forward. You must then tighten the mounting bolt.
4
If the hinges of your Cabinet are worn out and adjust the doors with their help it could not - replace the mechanism for a new, slightly changing the place of installation. To do this, remove the old hinge by loosening fasteners with a screwdriver. Mark with a ruler and pencil new position of the hinge mechanism on the doors and the sidewalls of the Cabinet. Drill the mounting holes and secure the new hinge with screws. Check your installation. If necessary, zashpaklyuyte old mounting holes.
5
Align the hollow paneled door kitchen Cabinet with door leveler. Fix the equalizer on the door so that it is located on its diagonal, from the upper loops to the lower angle. Tighten the equalizer to return the door to its rectangular shape. Note that this tightening should be performed slowly to ensure that all the shifts in binding occurred uniformly.

Strengthen the connection of the door by installing corner ties from the inside or scoring the wooden spikes.
Note
Doors for cabinets Quasar own making are of aluminum frame, light weight, reliable locks and modern look. QUASAR mirror doors for built-in wardrobes. Built-in wardrobe with sliding (bottom) and double (mezzanine) doors QUASAR. Flush handle for Cabinet doors.
Useful advice
These doors comfort contribute to the preservation of woolen and fur clothes from moths, as the air in the cabinets with exterior louvered doors dry and unfavourable for insects. The door in the bathroom and the bathroom. Cabinet doors can transform your old furniture beyond recognition.

Advice 2: How to adjust Cabinet door-coupe

Wardrobe is often confused with a pull–down module or built-in wardrobe. This is wrong; the main difference and perhaps the main plus of the wardrobe, that its doors ride on rollers on rail. What could be simpler: push – open, push – closed. Sometimes easy and soft movements of the door must be adjusted.
How to adjust Cabinet door-coupe
You will need
  • - Allen key 4 mm;
  • pencil;
  • - flat-head screwdriver.
Instruction
1
Dip one of the corners of the door, for example, the left. Use the hex key counter-clockwise twist of the bottom screw. Your Cabinet door will fall. Adjust the door so that the gap in the position of the left roller was 4-5 mm.
2
Adjust the right roller in the same way as the left. Lift the corner of the doorby twisting it clockwise with the key adjusting screw. Get the perfect position of a door of your closet-compartment, for this, adjust the position of the canvas so that the gap was 4-5 mm and the door of the compartment to the sidewall fit very tightly.
3
Adjust the stoppers. To do this, push the door of your wardrobe-a compartment to the side panel and put at risk the pencil in the area where the center roller is on the bottom rail. The door slide to the side. Slide the stopper with the flat screwdriver so that the marked line coincides the center. Check the door: close it and see if the door hit the stopper wheel, and clung to the sidewall, everything was done correctly.
4
If when checking the door of the wardrobe-compartment formed with a side clearance, slide closer to the sidewall of the stopper. If not, the stopper does not reach, then move, but just a little bit, stopper back.
Note
Follow up, keep in mind that the surface is uneven. So, you may have to set the wheels differently. Also, sometimes perfectly adjust the door does not work. Typically, adjustment screws do not withstand great stress and, if you will very much push on them, they will become worthless. Do not adjust the time, otherwise the wheels will deteriorate.
Useful advice
If you have the desire to achieve a smooth closing, then use the closer. Closers designed for doors weighing from 20 up to 60 pounds. Distinguish the right (R) and left (L), respectively, for right and left doors.

Advice 3: How to adjust Cabinet door

In the process of assembling the furniture when you move after transportation or long-term use is often required adjustment of the doors. Depends on its appearance. Independently perform the adjustment of the doors is a snap, with a minimal set of tools.
How to adjust Cabinet door
You will need
  • Phillips screwdriver
Instruction
1
Inspect the door of the wardrobe. Adjustment to the left or right is required when the gap between the two doors is uneven or the doors outside of the Cabinet. You might also need adjustment of the door height. If doors are uneven adjoin, to adjust their position by moving one of the adjacent angles forward or backward. If the method of fastening the door of the closet slightly different and the door is not installed above the doorway, and inside it, in this case, the loops are of slightly different design, but the adjustment remains the same.
2
Open the door of the Cabinetrequiring adjustment. Turn the adjusting screw located in the body of the loop, closer to the door. It serves to adjust the door left or right. Get that butt doors completely coincided with the end of the Cabinetand the gap between the doors was uniform and coincide with the gaps on other fronts, if they are available. If the door has a lock, it needs to function.
3
Unscrew a few turns the screws that secure the hinges to the body of the Cabinetto raise or lower the door. The holes for these screws in the loop are not round, but oval in shape, they are located vertically. Move the door along with the hinge slightly up or down to desired position. If the door is large, you can help yourself with a toe. As a result of such adjustment, the adjacent corners of the doors must match each other.
4
Loosen the screw located in the loop second from the door. Now the door has the possibility to change its position in the plane back and forth in the area of the loop. This kind of adjustment is needed and in that case, if the door is equipped with magnets.
Useful advice
The process of adjusting doors of the Cabinet are most effective if the Cabinet is installed correctly, its body is completely level and not twisted, that is, its internal diagonals are equal.

Advice 4: How to calculate the dimensions of the wardrobe

Wardrobes are essential ingredients for the modern interior. They can be very diverse, and using a completely different design elements. In short, properly selected and installed wardrobes can be a perfect decoration of the room.
How to calculate the dimensions of the wardrobe
You will need
  • roulette;
  • paper;
  • - handle;
  • calculator.
Instruction
1
Decide the location of future wardrobe. Often, especially in small rooms, the size of the wardrobe depends on this furniture accessory can be allocated a place.
2
After you decide the location of the wardrobe, pick up a tape measure and measure the height of the future Cabinet (as a rule, many prefer to install at home wardrobe up to the ceiling), its length and depth. Minimum recommended depth is 600 millimetres: approximately 100 mm will go to the sliding system, and the other of 500 mm and will fit hangers with clothes. Record all obtained measurement data.
3
Go to the detail of the size of the wardrobe. Remember that in essence it consists of a rack-box with lots of shelves and sliding doors. When performing the calculation immediately reduce the Cabinet height to 40 mm: still so much to take will be adjustable legs. So the wardrobe will consist of two steveh (Stevie is a vertically arranged stand made of particle Board): the length of these elements is equal to the height of the wardrobe, reduced to adjustable feet and a width of the back of the wardrobe.

Next, determine the size of the top and bottom of the Cabinet: these two parts are equal (the length of this element is equal to the length of the wardrobe and the width is the depth of the wardrobe). Determine the size of the Central steveh: depends on the height of these components from the desired height where is placed the rod for hanging clothes. In most cases, the height of the Central pillars is 1900 mm. Determine the number of shelves and, on this basis, calculate their dimensions and the gap between them.
Note
Producing calculations of individual parts of the design, consider the thickness of the chipboard! It may be different: 16, 18 or even 22 mm.
Useful advice
The number of doors in the closet is determined by the size of the structure and the important condition that the width of one door leaf should not be greater than 1000 mm.
Is the advice useful?
Search