Advice 1: How to fix chipped tile

Over time, unfortunately, even on the most beautiful ceramic tile appear chips and cracks. Of course, this tile can be replaced. But what if the in stock ceramic tile was not, and to contrive a Grand renovation no funds? In this case, to return the former appearance of the tile by its restoration.
How to fix chipped tile
You will need
  • - screwdriver;
  • knife;
  • - spatula;
  • - epoxy adhesive;
  • - grout;
  • fine - grain sandpaper;
  • - paint;
  • - alabaster;
  • - special correctional facility.
Instruction
1
Remove with a knife or screwdriver behind the entire wall or floor ceramic tile (shoot, even if the tile breaks off parts). Then with a spatula clean the reverse side of the tile and the cell from the adhesive cement.
2
Then cover sections of the wall or floor, which were removed ceramic tile with a thin layer of epoxy glue. With epoxy glue glue a broken ceramic tile.
3
The reverse side of the tile also smear epoxy glue and prop it up against the glue surface, then slightly press down and leave to dry.
4
When the tile has dried, treat the tile joints with grout, mixed with epoxy glue.
5
If the chip on ceramic tile, small, and replace the tiles is not possible, try to treat this defect fine-grained sandpaper.
6
Then fill the chip with paint in advance of choosing it in the tone of the tiles.
7
Fill in the crack or chip on ceramic tile plaster and then cover the top of the restored part of the tile paint to match tiles.
8
Carefully read the annotation to a special correctional facility. Then Unscrew the cover (it is attached to the tassel). This tassel type of bubble mixture and apply it on the damaged tiles. This tool dries fairly quickly (in a few minutes you will be able to estimate the result).
Note
Before using the correction tools test it on a waste piece of tile.
Useful advice
Below extending from the junction of the epoxy adhesive is not frozen on the face of the tiles before you glue the individual elements of a broken tile, oil the face of the tile with vaseline (after drying speaking of epoxy glue, remove with a chisel).

Advice 2: How to fix skol

From chips, no one is immune. Even on the new bathroom you may receive such an undesirable element. Of course, no desire to change the bath to put a liner or to emulirovat one single chip. What should I do? To remove the chip, of course. Of course, you need to understand that perfectly match the shades in halftones is obtained infrequently, so even the naked eye will be visible where it was chipped. Still, it's better than leaving things as they are.
The chip or crack is no reason to change the bath
You will need
  • Autosplice any. You should take a tube of small size and bright colors it is better to certainly not color their way through the enamel;
  • A fine-grained emery paper;
  • Enamel bath;
  • Abrasive polishing paste;
  • Tinting paste (if you do not have a white tub);
  • Construction (can be regular), the Hairdryer;
  • Solvent for degreasing the surface of the bath;
  • Polishing paste and felt.
Instruction
1
Clean the crack or chip to the steel color, then dry with a Hairdryer, then degrease the cleaned area with some solvent or acetone.
2
Prepare the putty, apply it to the chip and allow to dry for about 15-30 minutes. The drying time of filler depends on its grade. After drying putty sand it with sandpaper until the disappearance of the slightest bumps. Even better would be to smooth out the putty with a little pressure so that it is up to the level of the bath is not reached quite a bit. Then still enough space for the enamel. Then again, degrease and dry the surface with a Hairdryer.
3
Next is preparing the enamel. Take one part of hardener and four parts of the framework. If needed, add in the color. Kohler much to add not be (enough for 5-7%). Cover the prepared enamel place of cleavage. Allow the enamel to dry.
4
As soon as the enamel has dried, RUB the spot fine sandpaper. Then Polish with polishing paste and felt. So you get rid of traces of "grain" emery paper and finally will align the place of cleavage. That's all.

Advice 3: How to fix a chipped bathtub

The formation of a chip in the enamel, most unpleasant event, spoil the appearance of the tubs, especially if it has formed the most conspicuous place. The cleavage exposes the metal base bathtubover time the metal to start to rust and form unsightly stains.
How to fix a chipped bathtub
You will need
  • Restorer enamel, hair dryer, degreaser, automotive putty light shade, sandpaper fine grit, enamel bath, Kohler, abrasive polishing paste.
Instruction
1
In specialized stores presents reducing enamel coatings. Restorers enamel will help to get rid of scratches, chips and cracks. Pre-process an emery paper fine grit to be the restoration of the surface, degrease with solvent or gasoline, wipe dry. Do not wipe the prepared surface with a cloth – will be lint and dust. For drying, use a Hairdryer.
2
Apply with a brush, which is included in the scope of a reducing agent, a thin layer of reducing agent which will give an opportunity to repair the chipped tub. After the first coat is dry, if necessary apply a second coat. Enamel fully hardens after 24 hours.
3
If you buy the restorer of the enamel is not possible to remove the chip it is possible the other way. Clean the chip or crack in the steel color with the help of sandpaper, dry it thoroughly with a Hairdryer, a degrease clean area with acetone. Prepare and apply on a chip automotive putty, allow to dry for approximately 15-30 minutes (depending on grade putty).
4
After drying putty, sand it with sandpaper so that there were irregularities and bumps. Sweep produce a little pressure in order to coat was slightly below the level of the main surface. Therefore, the enamel will form more evenly. Again, degrease and dry.
5
Prepare the enamel in accordance with the instructions in the manual. If necessary, the composition add color. Enamel place of cleavage. Allow to dry. After drying enamel, RUB the treated area with emery nulevkoy. Then abrade with a piece of felt and polishing paste.
Useful advice
The appearance and service life of the bath is directly dependent on the conditions of its operation. Do not drop heavy objects on the surface of the bath and pour boiling water there.

Advice 4: How to remove the scratches on the car

Large and small stones flying from under the wheels of a car passing and oncoming traffic, hit the paint and cause chips. Such damage should be repaired immediately to prevent corrosion. Try to restore the surface on their own.
How to remove the scratches on the car
You will need
  • Car shampoo, fine abrasive and polishing pastes, tinting wax crayon, a napkin for rubbing, and auto-dash or auto-marker or the set for touch-up chips, consisting of paint and lacquer, toothpick (match), adhesive tape or masking tape, sandpaper No. 2000, solvent, rust Converter.
Instruction
1
Correctly choose the color of paint and grease pencil to repair. This is extremely important for local car repairs. If the chip long, treat it with rust Converter. Thoroughly wash damaged area with car shampoo. Otherwise you'll have to degrease this place, for example, benzine, white spirit or vodka. Dry the surface.
2
If the damage is only chipped paint, and the primer has not disappeared, put on a chip abrasive polishing paste. Wait 5-10 minutes and power trowel the area. It will zapolirovat. Then treat the injury fine polishing paste. The chip will be invisible. In this way you can efficiently align height and color of even a fairly large scratches.
3
If the paintwork is damaged along with the primer to the metal or repulsed plot wide before polishing gently apply to the location of the chip a bit of paint in the color of the car. Allow paint to dry. Next, apply the damage to the polishing with abrasive paste. Dry it for 5-10 minutes, then RUB and Polish it with fine polishing paste.
4
Use to conceal chips, wax crayon. Paint over cracked paint, remove with a tissue excess wax and Polish the location of the chip until smooth. Durability of such treatment is low. Probably going to have to repeat.
5
Remove the damage using the set for touch-up chips. In order not to smear the excess around the pre-paste over the damaged area around the perimeter of the adhesive tape or masking tape. Use this kind of protection after the repair can easily be removed from the surface of the car. Tint in two or three layers. Coat of paint make fine. Let dry and paint again. If just does not work smoothly and beautifully, or left stains, remove excess paint by blotting it with a cloth soaked in solvent. Dry the paint. Cover the top layer of varnish. If the chip is small, apply a drop of paint on the toothpick or sharpened match. In an hour – a drop of varnish. 3-7 days protruding nail Polish with emery paper # 2000, then abrasive and fine polishing pastes.
Note
Repair chips spend at a minimum temperature of 15 degrees, in dry weather, or indoors.
Useful advice
In the case of deep chips and scratches, as a rule, require more complex repair using filler, primer, paint and lacquer. And sometimes repainting the whole part. Contact a specialized shop.

Advice 5: How to close up interpanel seams flat

One of the most common disadvantages of prefabricated houses – poor sealing of interpanel seams, which with the onset of the rainy and cold weather, the residents begin to clearly feel podawania from cracks, moisture and other nasty consequences. If your management does not hurry to close up interpanel seams on the outside, at least try to close them from inside your apartment.
How to close up interpanel seams flat
You will need
  • - metal brush;
  • vacuum cleaner;
  • - sponge;
  • - polyurethane foam;
  • tape PSUL;
  • - polyurethane insulation;
  • - wooden shovel;
  • the mastic or sealant.
Instruction
1
Remove all the trim from the inside wall, Wallpaper, drywall construction, ceramic tile, etc. Completely embroidered seam and clean it of debris. Not wishing to remove all of that flaking and falling off. Preterite all seams stiff wire brush, then mimetite all the trash. Use a vacuum cleaner with a long nozzle to clean the crack of debris and dust, if possible wipe it with a damp sponge.
2
Pick up polyurethane foam insulation, thickness of seam a little more (10-20%) and cutting it to fill the entire gap, with minimum number of joints. Please note, along the material to cut is impossible, because it loses its properties. Can be used as a hollow (tube) and solid insulation.
3
Take a can of foam and fill the seam along its entire length, using a gun with a long nozzle. Do not try to fill the seam completely, keep in mind that the foam during the expansion will increase by approximately 3 times. It will fill all voids and cracks and hardens only through the day. If the seam through, try to protect the foam from exposure to direct sun rays, paving the seam before filling the wide tape PSUL.
4
Not waiting for the moment when the foam hardens, right in her place polyurethane insulation. Using a wooden spoon to tamp it into the seam, being careful not to break accurately along the length of the dock.
5
Lay the insulation in between the panels the seam is tight, but not very deep, it must not protrude from the seam, but at the same time, should remain a place for mastic. Therefore, place it so that there is an indentation in mm. 1-3 once the design hardens, apply sealing paste, for example, any domestic sealant.
6
Instead of a heater can use shtukatury composition. In this case, fill the joint with 2/3 foam, and the rest of the seam, close the cement-sand mixture razed the seam with the inner wall. To avoid drying out and cracking of the seam, from time to time obrushivaet it with water, especially if you have time work on Central heating.
Search
Is the advice useful?