Advice 1: How to repair a water cooler

Today, the use of clean bottled drinking water, rich mineral complex and other nutrients, no one believes another's whim. Especially convenient to use coolersdesigned for both cooling and for water heating. But, like any other technology, they eventually have to fix.
How to repair a water cooler
You will need
  • - napkin;
  • detergent;
  • - clean sponge for dishes;
  • - the appliance;
  • - screwdriver;
  • - fuse;
  • - the bottle.
Instruction
1
Malfunction in the water dispenser can often be caused by strong contamination of the device. Because of this clean the cooler. For a start, unplug the unit from the outlet and remove the water cooler bottle.
2
Gently and thoroughly wash the surface with dishwashing detergent. Pay special attention to the area around the needle (the place where is put a bottle of water).
3
Carefully remove the tray and thoroughly rinse it, then rinsing under running water.
4
All elements of the cooler, wipe it clean with a dry cloth.
5
Then insert the pan into place, install the bottle and grind a few cups of water (this will rinse faucet, which will prevent the ingress of detergent in water).
6
Turn on the cooler in the network and allow cooling and heating of water. The holding of such cleaning helps to avoid dirty particles into the mechanism of the cooler, and thus prolong his work.
7
If the cooler is stopped to heat the water, check first, and if it is included in the socket and is pressed on the device panel, the "enable" button. If after switching the device on, the indicator lamp still does not illuminate, verify that the outlet. This will include any other instrument. In that case, if the cause is in the socket, move the water cooler to another location, where nearby working outlet.
8
If the reason still lies in the cooler, then use a screwdriver to Unscrew the back panel of the cooler, remove fuse and, if blown, change it for a new one. If after the undertaken actions, the device still does not work, perhaps out of order, the heating element is cooler we need to get to the service center.
9
If the cooler is leaking water, the cause usually lies in a cracked plastic bottle — replace it with a new one.
Note
In any case, do not attempt to repair the water dispenser, under warranty service!
Useful advice
More serious problems will help solve the specialists of the service center.

Advice 2: How to make spinning cooler

Inside the system unit of a computer equipped with special fans. Their primary purpose – provision of cooling devices are important. The failure of one of coolers can result in the overheating of several PC elements.
How to make spinning cooler
You will need
  • - Phillips screwdriver;
  • - silicone grease;
  • - tweezers.
Instruction
1
If you notice that one of the coolers stopped working, first check the cause of the problem. Open the BIOS menu and make sure that for Fan Control is not set to Disabled. If the cooling function is active, turn off the computer and open the system unit. Find out whether you have connected the power cable of the cooler. Usually fans get the necessary electricity through the contacts on the motherboard or device to which they are connected.
2
Try to connect the cooler cable to the other connector. Turn on the computer and check the functionality of the fan. Try to turn the blades of the cooler. Sometimes the disconnect device is the presence of large amounts of dust. If the fan is not spinning, then again power off your PC. Unplug the fan and remove the device. Usually this requires you to Unscrew a few screws or special clips.
3
Remove the sticker from the fan and drip some lube into the open hole. Move the fan blades to allow the lubricant to be distributed along the axis. After that, the blades should rotate freely.
4
If the sticker you find the plug, remove it from the slot and carefully remove the snap ring. Remove the blade off the shaft and clean both with a dry cloth. Lubricate the axis of rotation and assemble the fan.
5
Connect the device to the system Board and install it in place. Turn on the computer and make sure that the fan is working properly. If none of these methods helped to restore the efficiency of the cooler, replace the device.
Note
Do not use the computer with the faulty fans. This will lead to overheating and damage to important devices.

Advice 3: How to repair the soles of shoes

Of all component parts of the Shoe most likely to damage and wear prone to sole. Method of repair depends entirely on what material it is made and how is attached to the top of the Shoe.
How to repair the soles of shoes
You will need
  • - Gasoline
  • glue 88Н
  • Shoe spokes
  • - dratwa
  • Shoe options
  • Shoe rasp
  • pieces of polyurethane
Instruction
1
The place where the departed polyurethane sole, clean from dust and dirt and degrease with gasoline. Then at the same location, remove the flat needle files painted a layer of skin, and again perform degreasing. Heat the electric soldering and gluing on the skin and smooth cut from the soles of old pieces of polyurethane. Squeeze the top of the Shoe and sole , and hold them heated part of the device for a burning out, treat the area of bonding. While zaglubljaja heated element to postilki. It is important to precisely follow the temperature of the heating device and the pressure between the top and sole, which will require a certain skill.
2
If the edge is overlaid with polyurethane soles up, on the cleared and fat-free area, apply a layer of glue. Then soak 15 minutes, squeeze the sole to the top of shoes and sew grated Shoe pitch stitch. The seam must go to a distance of 5 mm from the top edge. If unstuck sole – rubber, skim the repair, apply the glue and after 15 minutes of drying pressure-tested shoes.
3
If the rubber sole is drifted, it is necessary to align the Shoe rasp and degreased gasoline. Also degrease the soles of finely porous rubber. Cover the trail and the sole of a thin layer of glue and, after 10 minutes, glue the way forward. Acting for the sole edge of the track cut away with a knife, align the rasp and smoothen the abrasive cloth.
4
To repair the leather solesneed sole of similar material. Place the sole on a metal surface such as iron or an iron anvil, with flesh side up. A heavy mallet with a large bacom, emboss it, starting from the middle. Place embossed soles on the soles and at the time we secure it with a couple of nails. Cut the edge and sew, pre-cut by one-third the thickness of the groove in which the seam will be hidden. Sew a sole using a Shoe needle stitch, grated shoemaker's pitch. After sewing it over the slot with glue and hammer to close it.

Advice 4: How to make face cream

Homemade creams have advantages over industrial cosmetic products: they are made from natural ingredients, you can always check their quality, self-made creams no preservatives.
How to make face cream
You will need
  • - lanolin;
  • - glycerin;
  • - essential oils;
  • - beeswax;
  • - vitamins in the adipose capsule;
  • - dry herbs, vegetables, fruits, etc.
  • - capacity for melting the composition;
  • - measuring syringe;
  • - mixer or a blender;
  • - a stick for stirring.
Instruction
1
Determine the type of creamyou want to prepare, moisturizing, nourishing, softening, anti-aging, etc. depends on the composition of the cream and select ingredients.
2
Get all the ingredients homemade cream – the pharmacy, a specialty store or a regular grocery store. All the dishes, which will be in contact with the composition, pre-scald with boiling water.
3
Make the base of the cream – it can be beeswax, palm oil or cocoa butter, and other solid formulations. Break into pieces or astrogate a solid Foundation, put them in a bowl and melt composition in a water bath.
4
In a separate bowl, mix dry herbs, pulp of fruit or vegetables, honey, glycerin, lanolin, etc. Mix all ingredients in a specified dosage, gently stir with a wooden or plastic stick, achieving uniformity of the composition.
5
Connect the two parts of the cream. In a bowl with the melted base in a thin stream, pour the second part of the composition. Whisk the cream with mixer or blender, achieving full dissolving and dispersing the components.
6
Add the water part of the cream – pour the cooked vegetable infusion (spoon dry herb per Cup of boiling water), mineral non-carbonated or distilled water. Put the entire composition in a water bath, soak for 3 minutes and transfer a container of cream in a bowl with cold water. Immediately start whisking the cream with a mixer and continue until, until the structure finally cools off. At the end of churning, add the prepared essential oil and vitamins (so the oil trains will retain all its useful properties).
7
Place a container of homemade cream in the fridge. During use, keep in mind the expiration dates of improvised compositions – usually they do not exceed seven days. The best way to store homemade cream in glass jars, and get them need special spatula and not fingers.
Search
Is the advice useful?