Connect the USB adapter that comes in one set with the mouse, into the USB port of your computer or laptop. Wait for determine the connected device in the operating system, following the notification displayed in the system tray. After automatically detect the driver for mouse Genius, you can proceed to the wireless connection of the mouse.
If Windows has issued a notification that the drivers have not been installed, insert the software CD that came with the mouse into the disc drive of the computer. If you drive there, go to the official website Genius. Click on "Drivers" at the top right of the screen. In the list that appears, select "mouse". Click the model of your device and download the files to install the drivers for the right version for your operating system you can specify in the list.
After downloading the installer for the driver, run it and follow the instructions on the screen. After notification of the completion of installation, restart the computer to apply the settings.
Remove and then again insert the wireless adapter of the mouse into a USB port. Install the batteries in the mouse. In the presence of switch power on the mouse, move it to the On position. If the regulator is missing, after you install the batteries the sensor power supply will immediately turn red.
Press and hold the Connect button on the bottom of the mouse. If the key is present on the connector, and hit it, and then wait for establishing connection between the device and the wireless adapter. The Connect button on the mouse and on the adapter need to press at the same time. After about 5-10 seconds the device will be identified and you can begin using them. If the connection fails, remove the connector Genius from the USB port of the computer and try to create the connection again. Setup is complete.
Advice 2: How to install a wireless mouse
Wireless mouse is an extremely convenient device that allows you not to be attached to the computer, and, nevertheless, operate it like a normal wired mouse. Wireless pointing devices of different manufacturers may differ in some features when you install and connect to computer. However, there are some General rules that allow you to quickly install a wireless mouse.
The set of wireless devices includes the USB adapter, driver CD and the mouse itself. The first thing to do is to install the driver into the operating system. Insert the ROM supplied in the drive; if the autorun started, the drivers installed themselves. If nothing happens, open the disc in Windows Explorer and look for files with names “Install.exe” or “Setup.exe”. Start them now.
Plug the wireless adapter into the USB port of the computer. The system will detect the new device, scans for drivers for it and will report about the successful installation of the equipment.
Be careful with the batteries for the mouse, if they are not included in the package. After the detection of the USB adapter, insert the batteries in the mouse. Normally, this is enough for installation and determine the wireless mouse. Rarely, you may need to restart the computer.
Some models are equipped with additional buttons for adjustment and settings of the adapter and mouse signals from each other. If your devices are switches there to click them. In some models, the wireless devices need a few seconds to hold these buttons pressed. Do I need to do it for your wireless mouse, or tone settings of the adapter and the mouse occur in any other way, you should read the user guide.
Advice 3: How to connect headphones
Headphones Genius that go along with the MIC, is no more difficult than connecting these devices to the computer separately. The key thing here is not to confuse one with the other connector.
You will need
Make sure that your sound card has the necessary driver. If you have a regular computer, turn the system unit and locate the connectors of the sound card. There may be two, three or even more 5 - it all depends on its type. You need green and pink.
Also note on the side wall of the housing and its front panel – a modern computer model output sockets for headphones so you don't have to turn the system unit when connecting devices. Many keyboards and monitors can also serve as transitional devices for headphones and microphones.
Connect the microphone cable to the connector on the computer with the corresponding pictogram, plug from the headphones into the connector next. Follow the color scheme of the connection or pay attention to labels and icons, they must match. Usually the connector for a microphone is to the right, however, it may depend on the model of sound card of your computer.
If you have a laptop, look on the front panel of the housing connectors of the sound card. They can also be on the right and left sides of the device. Also, be color scheme, and follow the steps in legend of pictograms and inscriptions, do not forget about the necessity of installing a device driver.
In menu "control Panel" to navigate to settings, sounds and audio devices, change them according to your desire and make sure they are correct, for example, making a trial in the special application service "Skype" and so on. If the device does not work, check the volume on the sound card in the notification area, adjust volume level of the program and a special switch on the wires headphone Genius, which happens in some models.
Pay attention to the icon when connected.