Advice 1: How to connect a light bulb

If you need to conduct rather complicated electrical work (for example, connection of the switch Board) decided to use the advice and services of a master electrician, then something will have to learn to do independently. For example, to connect a light bulb in there.
How to connect a light bulb
You will need
  • 1. The source of electricity
  • 2. Electroputere
  • 3. Plug electronica
  • 4. Cable cut
  • 5. Duct tape
  • 6. Knife for extraction and Stripping lived
  • 7. Screwdriver for fastening lived on terminals
Instruction
1
Locate the stationary source of electricity, nearest to the place where you need light the bulb. Best of all, if it's a socket mounted on all the rules and serviceable. Connect a portable light source to the wiring already connected and operating, be impractical, especially if the wiring is hidden.
2
Take electroputere, mains plugs and cut the cable of sufficient length (preferably with the stock, given the loss when connecting it to the plug and the cartridge). Wiring diagram for light bulbs will look like this: it is screwed into electroputere, which is connected to the cable with one hand, on the other it connects to the plug, providing the plug contact with the power source (via power socket).
3
Connect the cartridge to the cable, exposing the wires inside and strip them for good contact. Loosen the Chuck, pull the end of the cable into the input hole and secure the wires with terminals of the type used in the cartridge of this modification. Then connect the plug, unwound it and carefully connect the cable conductor with his other hand to the terminals.
4
Tape as thoroughly as possible the places where the cores of the cable is left open or where it damaged its insulation. The quality of the insulation depends on your safety and the condition of the appliances, so take this time, more attention, considering it not only a "reassurance". To the moment of switching the bulb cable along its entire length must be insulated carefully.
5
Now screw the bulb into the socket, so that it was clearly stated in it. The plug will connect with the socket to illuminate the bulb, you have created a plot of the electric circuit must be closed, that is, between all of its components must be contact. Like it or not, you will immediately see, unless, of course, the bulb is OK.
Useful advice
From "carrying" made in this way, you can make a fully-functional lamp, just enough to secure cable on the wall (or ceiling) using Chomutov, and a light bulb to hide under some shade.

Remember that not all ammo is designed for a powerful incandescent lamps - some of them may start to melt if the bulb power will be, for example, 150 watts.

Advice 2 : How to connect multiple light bulbs

One of the main requirements for the lighting of premises – functionality and efficiency. To ensure the apartment comfortable lighting, it is recommended to use the combined connection diagrams, while the luminous flux it is desirable to make controlled power. One of the ways to do lighting – connect multiple light bulbsthat will be included in a specific pattern.
How to connect multiple light bulbs
You will need
  • lamp (chandelier);
  • bulbs;
  • - connecting wires;
  • - the probe (the tester).
Instruction
1
Before production work on the installation of ceiling lights make sure that mains voltage is disconnected. Use this to check the tester or test lamp. Only after such verification, the luminaire should be mounted on a ceiling hook. Use for mounting a portable stable step-ladder. If necessary, make sure that during the production of works for connection of lighting you are insured assistant.
2
In the simplest case, apply the usual method of connecting a ceiling fixture or chandelier using a two-wire circuit in which all bulbs are included simultaneously. Wiring this connection is not straightforward.
3
If the chandelier is for five or more bulbs, mount the three-wire scheme. It will consist of one common wire and two sectional wires. For easy installation use the wires in the braid of a different color - this will help to avoid mistakes when connecting the scheme to the food.
4
In the presence of a series switch to make a circuit of light bulbs "2-3-5". This option allows you to use multiple methods to enable mnogoplanovo lamp, wherein the switch enables you to control the connection of lamps. In other words, you can only turn two lights, three only, and include all five lamps.
5
When mounting diagram with labeled wires connect the common wire of the chandelier and the neutral wire connected to the hook on which the chandelier is suspended. Phase hoses connect the hook with sectional wires. If the wires are not color coded, to installation, determine zero and phase wires with a probe. This will apply for wire tension, so be extremely careful. After identifying the purpose of the wire again, cut off the voltage and perform the circuit.
6
To all the lamps in the lamp was started at the same time, use the switch with one button, and the wires 2 and 3 (see figure in step 3) connect together and connect to the phase liner.
7
Connecting wires, install lights and attach the cartridges in the bulb. Connect the voltage and test the installed circuits. If necessary, correct any errors in the installation.
Is the advice useful?
Search