Advice 1: How to reset Epson CX4300 cartridge

Refill inkjet cartridges is a complicated process, which is followed by the leakage of ink and other problems using perenapravlenie cartridges, and reset the chipset often becomes a headache for users that are not familiar with the principles of programatora. For inkjet printer models were invented, the system of uninterrupted ink supply in which the cartridge reset is much faster.
How to reset Epson CX4300 cartridge
You will need
  • - the programmer.
Instruction
1
If you need to reset Epson CX4300 cartridge with a connected continuous ink supply system, wait until the system will fail due to the fact that the cartridge is empty. In accordance with the user move the position of the ink cartridge holder to the right side, then click on the desired casing of the cartridge, then the printer will reset and the update about your cartridge.
2
Purchase a special programmer to reset the printer cartridges. You can easily find it in stores radio your city or assemble it yourself by downloading from the Internet the chip. Disconnect the cartridges from the printer, perenapravit them, the Bay inside of the body ink of respective colors. The contact of the syringe with the cartridge seal with a good sticker. Do not use labels again and do not replace them with tape.
3
Remove the chip from the cartridge of Epson CX4300 and insert it into the programmer. Run the attached software and zero out the indicators of capacity of cartridges. Return the chip back on and install the cartridge into the printer. Perform a test print pages. If your printer is still not being used, the system is a continuous supply of paint, use it when printing large volumes.
4
Note also that the process of resetting the print cartridges when you use requires much less time, not to mention the process of refilling. To acquire a system of uninterrupted ink supply for Epson ink cartridges you can in computer stores in your city, as well as in retail outlets serving copy machines or ordered in the online store. Also try to choose the most suitable to model the ink cartridges to avoid the problems associated with printing. Ink is usually sold in large bubbles separately in each color or a set.
Useful advice
With a simple inkjet printer, turn the colored page every 1-2 weeks.

Advice 2: How to reset the printer cartridge

The situation when you have to reset the cartridges on the printer is quite common. This can be done in several ways.
How to reset the printer cartridge
Instruction
1
In the cartridges the printer has a chip, which contains information on the resource and on the number of already printed pages. When the cartridge indicates the need for its replacement, not necessarily that it is really empty, just the chip counted the number of pages needed. And the pages could be printed only a few lines. That is, the ink level in the cartridge is calculated by the program, and there is no information about the real situation. To solve this problem in several ways. To laser printerx, it is possible to replace the chip on the cartridge. There are chips for large quantity laser printers, there are universal chips that are suitable for a wide variety of printer models. In inkjet printerthis chip is fundamentally different and just replace it. In this case, you can hold the reset chip cartridges. The most simple solution is to carry out zeroing using a special programmers or reprogrammation. They are on sale or you can make them yourself. For self-reset chips, remove the cartridges from the printer.
2
In the service menu of the printer press the cancel button and press OK. After some time, release the buttons.
3
In the menu, select the Resets Menu, and then click OK.
4
Select Reset Partial and then again click OK. Then the printer is off.
5
Turn on the printer, select region and language to Europe.
6
After that follow the instructions will offer you the printer. Check what is the ink level. If he wasn't 100%, then repeat the steps again, but instead select Partial Reset Semi Full Reset. In some cases after that, you must repeat all the steps again, but with a Partial Reset.
7
Also try to click on the button "Reset/Stop" on the printer about 10 seconds. After that, the ink cartridge will no longer be tracked by the printer. For each color need to separately. Now the ink level need to monitor yourself visually.

Advice 3: How to reset chip for Canon cartridges

Reset chips of cartridges is a necessary condition for them to refill, as without this procedure it will appear in the system printer as empty. This kind of security system was invented by manufacturers to increase trade turnover, however, remember that occasionally a cartridge still worth to change to a new one.
How to reset chip for Canon cartridges
You will need
  • - programmer to reset the cartridges or utilities IPTool/ MPTool.
Instruction
1
Purchase compatible with your device ink refill. Need information on this topic you can find by running a query in a search engine, using as key words the model of your cartridge. Ink can be purchased at office supply stores as well as stores selling computers and peripherals. Don't forget that you can still order them via the Internet.
2
Purchase a special programmer to reset the chips cartridge. You can buy them in specialized stores maintenance of printing devices. Carefully read the instructions for use and remember that each manufacturer only fits one type of programmer, also they are still divided along model lines.
3
Use the mute function of monitoring the ink level. This is true for those models in which the chips of cartridges cannot be reset, and the last time. For this purpose, after the withdrawal of print that ink is running out, hit and hold for 10-15 seconds to activate the paper feed. After that, the control over the fullness of the cartridge is disabled and you can safely perenapravit it.
4
Use special tools and MPTool IPTool to reset the counter ink for the printer model series of IP and MP, respectively. After installation perenapravlenie cartridge in the printer, select CHANGE Model. Next, press command to reset the black cartridge RESET Black and RESET Color, respectively, for color. Then you can watch as the ink level rises to a value of 100.
5
If you have enough unsure of proficiency on office equipment, it is best to contact the relevant service center, which will help you in the shortest possible time to solve the problem with zeroing and refilling the cartridge.
Note
Use perenapravlenie cartridges in some cases, deprives you of the warranties provided by the supplier, the seller or the manufacturer.
Useful advice
Read the guide to recording apparatus before the reset the chip.

Advice 4: How to reset ink cartridge

When filling cartridges inkjet printers sometimes you need to reset their values, otherwise the print head cartridge will not move from his seat. To reset the chip inside the cartridge uses a special device — a programmer.
How to reset ink cartridge
You will need
  • - the printer cartridge;
  • - the programmer.
Instruction
1
If you encounter such a problem, it is necessary that you understand what you will do. Inside some cartridges have chips that count the amount paint or tiles, which is consumed during printing. Roughly speaking, the chip acts as a timer, at the expiration of the required values on its dial, the printing is automatically locked.
2
Typically, the chips of the cartridges that came with the printer, it is difficult to reset. You need to buy the same original cartridge for which it would be possible to reset the values. To perform this operation, use a hardware programmer. In appearance this device has a small size, about a couple of matchboxes or slightly more (depends on the model). On one side are the contacts and on the other lights, sometimes there are still some buttons.
3
For example, for cartridges from Epson printers, the order of actions is as follows. Open the printer cover and remove the cartridge by pressing a special button, which should light in red, since the paint came to an end.
4
Take the cartridge (black or color) in one hand and in the other hand should be a programmer. Align the terminals of the device reset with the cartridge contacts, then press the appropriate button. After turning signal indicator, disconnect both devices.
5
The same procedure repeat with the other cartridges, then insert them back into the tray of the print carriage. Close the lid and press the button again, signaling the small amount of ink.
6
Repeat print the open document, check the rate of ink through the printer driver. If the ink remained in the same position as before drop, repeat the process again.

Advice 5: How to reset the Epson cartridges

Cartridge reset – operation is needed for further refilling. All modern printers cartridges have a special chip that is programming it for a single use.
How to reset the Epson cartridges
You will need
  • - the programmer.
Instruction
1
Find computer stores in your city a special set for refilling ink cartridges Epson. This set includes ink or toner, and a special device to reset the chip – programmer.
2
Remove the cartridge from the printer and open the manual to the programmer. Read it carefully. Please note that the sequence of actions depends on the model of your cartridge, so even if you have previously performed a reset other Epson cartridges, in this case can be applied completely different course of action.
3
Following the instructions, do the reset the chip cartridge. Place it toner, pre-clearing the container and other internal parts with a cloth. If you do not, the print quality will suffer, the documents will appear streaks, stains, etc.
4
Use also another version of the kit for refilling cartridges for Epson, which includes the toner (or ink for inkjet printers) and the replacement chip. Also included is a detailed instruction on replacement of the chipset on the new, carefully follow her. Since this is a fairly complex operation, it is best to perform in the presence of a person familiar with the service of copy technics. After replacing the chipset pour the toner into the cartridge, make a sample print of the document.
5
If you have the skills radio, assemble the programmer yourself. For this you can use the information from this portal http://resetters.ru/index.php?showtopic=546. If you are not sure that you will be able to produce a reset of the chipset, contact the specialists of service centers. The use of damaged or improperly zeroed cartridges leads to breakage of the printer. Also, the use of perenapravlenie cartridges denies your warranty on the printer.
Useful advice
Not perenapravljat the same cartridge more than 5 times.

Advice 6: How to reset cartridge Samsung

Now very few people buy new cartridges for the printer. Most users have adapted to their dressing independently. Therefore, developers of printers was coined by a special chip in order not to lose the main source of income. The main objective of the chip is to block the ability to print after cartridge resources will be exhausted.
How to reset cartridge Samsung
You will need
  • - universal programmer.
Instruction
1
For the operation of the cartridge you just need to reset the counter chip. In fact, the data of the chip will reset and it again starts to count. To reset use a special device called a programmer. Of course, the device costs money. But it is better once to buy it and refill the cartridges yourself, than to buy a new one or to pay for their gas station service centers. Depending on the printer models, the cost of the programmer can vary greatly. You need to buy the model that matches the printer model.
2
For Samsung printers very popular universal programmer model, the principle of which is different from the others. For example, and examines the process. Find this model on the Internet. Just type "Samsung universal programmer".
3
Connect the programmer to the USB port of the computer. The further procedure will be described on the example of the Windows 7 operating system. On other OS it may be slightly different. Included with device is driver Speed prog. Install it.
4
On your desktop a folder will appear Speed prog. Open it, click file Speed prog. In the window that appears, click Test. After a few seconds the program will detect the chips. Click on the arrow at the top. There will be the name of the serial number of the cartridge. Select it. Then connect the chip to the programmer (described in the instructions).
5
Then in the program menu, select Read all. Save the file. This is an old version of the firmware. On this file (firmware) you need to open with the editor program. To know what values to change in the program instructions available in the folder on your desktop.
6
Then in the program window, click the icon corresponding to the first arrow, which is above, and select the file with the edited firmware. Then click Write all.

Advice 7: How to reset chip for canon printer

Printer - a versatile device to print the required files, photographs and other documentation. For some models the cost of buying a new cartridge can be very expensive. Therefore, many users have learned to fill them at home. But each cartridge is the chip that indicates the level in the paint. When self-refilling the chip stops working correctly, so it needs to be reset.
How to reset chip for canon printer
You will need
  • The program IPTool or МРTool.
Instruction
1
In order to reset the chip on printer Canon you need to install a program on your computer IPTool or МРTool (the first two letters is the model of your device). It can be either downloaded from the Internet or purchased in a service service center Canon. When you install the app, follow the prompts that appear on the monitor screen. When prompted enter the license key (if any). Please note that IPTool / МРTool presented in English only.
2
To begin the zeroing cartridge, purchase a suitable for your printer ink. Make the filling up to the possible maximum. Run the program. In the appeared window select the section of the Change Model, and the model of your printer. After that there will be functions to reset the chips of black and colored cartridge. Hit, respectively, Reset Black and Reset Color. This will start the program.
3
Upon completion of the application you will see a dialog box indicating that the operation was successful. When you access the printer menu you will see that the level of refilling the cartridge with ink has reached 100%. Decrease the percent value, respectively, will fall.
4
Some printers company Canon have protection against reset chips. In such case, you can simply disable the function of determining the level of ink charging. But then you have to control, when to refuel new batch of paint.
Useful advice
The program IPTool / МРTool can also be used to change other settings, printers Canon, as well as to control the operation of the cartridge: changing the value of the delay for drying, the ability to print a test page etc . If the application experiencing difficulties, please check its installation or entrust this work to professionals.
Is the advice useful?
Search