Advice 1: How to glue the car

Lining (padding) of the interior of the car is laborious and complicated, has many nuances. As we approach it for the first time, you need to be prepared for the fact that you have to put a lot of effort and spend a lot of time. However, those who are afraid of difficulties, do not have a right to expect success in any business.
How to glue the car
You will need
  • – material for pasting (avtokozha, Alcantara, fabric, felt or imitation leather);
  • glue;
  • – Hairdryer
  • – a tool (scissors, brushes, knife, etc.);
  • – sandpaper.
Instruction
1
Choose the right material for pasting the salon. It can be avtokozha, upholstery fabric, imitation leather, felt or Alcantara. The last material is an artificial ultramicrofibre of non-woven polyester fiber coated with polyurethane. Due to its strength characteristics, it surpasses even natural leather.
2
As glues are the best English Fentac aerosols and Tuskbond and German glue Kleiberit. The latter is particularly good for laminating items that are in the process of operation can become very hot from sunlight (dashboard, for example). Can also be used 88th and glue "Moment".
3
In General, the technology of pasting consists of the following operations: cutting of a piece of material of desired size and shape greasing adhesive (double – material and single – pasted over footage), overlay and clamp (stitched) material.
4
Before stick the skin to the surface of a convex shape, soak it in warm, but not hot water for about 2-3 hours. Stretch wet skin to be pasted on detail and dry with a Hairdryer in this situation. As a result, the material will take the form basically the details. Then RUB it twice with the glue drying layers, apply glue to the detail – also with the drying and tighten the skin on the pasted over land, simultaneously warming it with a Hairdryer. When the adhesive skin densely covered the surface.
5
And pasting the parts with too much variation in shape, before you label stitch material cover in the form of the part. Seams must be located exactly on the corners of the surface. From accuracy of manufacturing of case depends on the quality of laminated surface.
6
Other materials are not subjected to soaking. Just promazyvaetsya with the adhesive are dried and fixed to the pasted over surface. Drying the dryer in time stickers allows you to make the glue more soft and supple and provides the best adhesion. When spreading the glue Alcantara, avoid excess, otherwise it will show through on the other side and make the front surface hard, worsening its appearance.
7
Places with the joints, zapressovyvat the edges of the material in them with a spatula or a narrow screwdriver. At a particularly difficult edge the edge is shaped triangular petals, which when laying interlock with each other, forming on the crest of the fold.
8
At pasting of plastic surfaces to improve the adhesion, they can be treated with sandpaper. In those places which are difficult to paste accurately, apply the decorative elements of Alcantara. They will help to disguise the flaws.
Note
If the vehicle is equipped with airbags, an adhesive material should not overlap the joints, which should open up the emergency system. Otherwise, the pillow is not the right time to be revealed. There are two way of obtaining the emergency joints – cut material at the joint and joining him in this spot by a thin thread. In both cases, the material straining at the junction at the time of activation of airbags.

Advice 2: How to glue film auto

In its technology wrapping car film can be "dry" and "wet". The first method is more suited to professionals. Those who engaged in it first, better to use a "wet" method. In its application to the vehicle is applied to the emulsion prepared from water and some detergent – for easy installation of the film.
How to glue film auto
You will need
  • – vinyl film;
  • – stationery knife;
  • – plastic or rubber spatula (squeegee);
  • felt spatula;
  • – industrial or Amateur Hairdryer;
  • – spray bottle filled with water with a detergent (Fery, soap, etc.) in a ratio of 10:1;
  • – rags;
  • – adhesive tape.
Instruction
1
Thoroughly wash the car. Clean the surface from any contamination. From the surface cleanliness depends on the quality of gluing, the body must be absolutely clean. If it has traces of oil or grease, clean them with a weak solution of some degreasers (mineral spirits, etc.).
2
Try film together with the substrate and mounting tape to the area you want to Wallpaper. The film can be stick on the whole car at once, but easier to glue the individual pieces on the doors, hood, trunk, etc. Carefully cut the film around the perimeter of the area with a utility knife, passing the knife into the gap between sections – for example, between the door and the body. If the zones are not separated by a junction, use as labels, delimits the zone, masking tape, pasting it to the body.
3
Put the cut piece of film on a flat clean surface face down and carefully remove the backing paper. Ensure that the folds of the film are not glued together. One perform this job difficult, you need to have an assistant.
4
Spray the sprayer with water-soap emulsion to be pasted on the area of the car. In this case the entire surface, with no gaps. It is better to apply the surplus of the solution than to leave any space dry. Emulsion need for protection from premature adhesion of the film to the car for its styling.
5
Put tape on the area so that it got to its exact position. When fitting nudge her in the right directions, water-soap emulsion will allow you to do this easily.
6
Start the paper priglazhivaniem film using a rubber spatula, starting from the center and moving to the edges. Thus heated film dryer – be very careful not to melt it. Occurring irregularities (handles, moldings, etc.) skip, not confining them to the end. Their turn will come later.
7
First, roll the Central area, leaving edges are not firmed. If in places of transition of planes formed in the folds, peel the film from the body and heat it, the crease should disappear. After smoothing the Central zone of the roll places the irregularities that were skipped during the original stickers. Actively use the dryer for heating and stretching of the film in difficult places.
8
After all the film will be pasted, take a felt squeegee and push with it the air bubbles and soapy foam from the center to the edges. If there are bubbles that are impossible to kick out, heat them with a Hairdryer and pierce. The small bubbles disappear on their own after 1-2 weeks.
9
After completion of the work with the Central area, roll the edges of the film, cutting off the excess. Covered with wipe the spot with a dry rag and leave the car for a day for the "seizure" of the film. Do not wash it for one week.
Note
During gluing the temperature should not be below +20°C. the Room must be clean – without dust, insects, poplar fluff, etc.

Do not wet the backing paper of the film, it will complicate its removal.

Avoid overheating of the film with a Hairdryer to prevent it from melting.
Is the advice useful?
Search