Advice 1: How to fix leaking pipe

Damage to water pipes can occur for two reasons: corrosion and deformation caused by physical impact. Corrosion of exposed metal pipe, while from mechanical damage not insured there is no pipe. There are ways to stop the leak on their own before the arrival of the plumber.
After elimination of the leak and repair the cause of povedeniya pipe
You will need
  • 1-2 clamp diameter
  • rubber band
  • sealer
  • wire
  • adjustable wrench
  • oil paint
Instruction
1
The fastest and most reliable way to eliminate the leak is to put a clamp with a rubber gasket. First, you must shut off both hot and cold water valve. Unscrew the bolts, put on the leak rubber seal and wrap around the seat clamp. Remember that the bonding clamp is necessary on the opposite from the hole side, otherwise the commit will be loose. Tighten the screws you need a wrench. If the leak is large, then it may need 2 clamps with thread. In this case, a dense piece of rubber is applied to the leaks, top and bottom overlap the clips. These clamps can be tightened with a screwdriver.
2
If you can buy clamp no, then you can fix the leak by tying it with a rubber band. It can be cut from a Bicycle tire, and other handy materials. On top of the tape should tightly wind the wire tightly stacking the coils.
3
If the leak occurred near the thread, then eliminate it by overlaying rubber band. Dip it in oil paint and then wrap the junction. When the paint dries, the hole is securely sealed.
4
Of course these are all temporary measures. If the pipe is damaged from rust, it is necessary in the first case, to replace the entire pipeline. If the pipe burst from excessive mechanical stress, it is necessary to further protect it from possible impacts. The place of the leak, you need to solder.

Advice 2: How to fix the leak in the radiator

Leaking coolant from the radiator is always usually a surprise to many owners. Appears similar fault for various reasons. Among them: long life of the vehicle or poor quality antifreeze, filled the cooling system, which result in corrosion destroys the metal tube of the radiator.
How to fix the leak in the radiator
You will need
  • Silicone sealant for radiator
  • soap
  • knife.
Instruction
1
Driving practice has several ways of removing coolant from the radiator. And just what do not give advice about it "seasoned" masters. Among the popular methods to stop coolant leak, widely used such a method as adding the antifreeze silicone sealant which is poured into the expansion tank when the engine is not running. Then the motor starts and let it run for 15 minutes. For a specified period of time, a leak will inevitably stop.
How to fix the leak <b>radiator</b>
2
But sometimes circumstances are such that at hand at the right moment may not have the bottle of sealant. In this case, you can restore the integrity of the radiator with suspenders ordinary soap that you want to add in the form of chips in the surge tank. Approximately 50-100 grams of soap is cut with a knife, and then soap flakes is added to the cooling system. Despite the singularity of the method eliminate the leak of the radiator - it is quite effective, and allows you to overcome by car, with a similar malfunction, not one thousand kilometers.
3
Be aware that these methods eliminate the leak of the radiator are a temporary measure to help them get to the faulty machine to the nearest service stations, and produce there a full reconditioning of the cooling system.

Advice 3: How to fix a leak pool

One of the most common technical breakdowns of the basin is leaking water. Note that self-repair of the pool can be performed only in the case if you built the pool with their hands and thoroughly understand its structure. In all other cases, to eliminate the leak in the pool, it is recommended to turn to professionals.
How to fix a leak pool
Instruction
1
Make sure you have protective actively working heating system or a hot period, the water from the pool may simply evaporate. Put into the pool barrel so that its edge protruding from the water a few inches. Fill the barrel with water. The water level in the barrel should match the water level in your pool. Mark the water level on the wall of the barrel with a marker. Compare the water level in the pool and in the barrel at the end of the day. If the water level in the barrel is greater than the water level in the pool, so the pool has a leak.
2
Find proteocephalidae place during the day rate of leakage of water when the pump. Record all measurements on paper. It is desirable to perform measurements every hour. Disconnect the circulation system and guide the same measurements. Compare the results obtained.If the water is faster out of the pool when the pump, the cause of the leak, most likely is a malfunction of the water supply system of the pool. The most vulnerable places are: the return pipe, the connection pipe from the rear part of the port located on the wall of the pool; a filter in place of the water passage through the gasket in the filter head; the suction pipe of checkoutdate, at the junction of the pipe with checkoutplease.If water loss is the same when turned off and on the pump, most likely a leak occurs in the frame of the pool. The most vulnerable point in the design of the pool is considered to be a hydrostatic relief valve located at the bottom of the pool, at the main sink. Also, pools with a vinyl coating, water leakage from the housing pool may occur due to the formation of holes in the coating. Concrete swimming pools may cause cracks in the Foundation.
3
Repair protechmedia eliminate leakage in the pipeline is necessary to hold test pressure in the pipeline system or to use a special paint for testing pools. This is necessary in order to accurately set the location of the holes. Getting to the location of the leak, the paint leaves a mark. Find the location of the water leak you will be able to fix the leak in the pool, replacing the damaged parts of the pipeline.To eliminate the leak in the frame of the pool need to be drained from the pool all the water. If necessary, repair or replace the waterproofing of the pool. For the repair of the concrete frame of the pool you can apply a special PVC membrane that is fastened on top of a leak or sealants are designed specifically for swimming pools.

Advice 4: How to fix scratches on plastic Windows

Plastic Windows have several advantages over normal wood. This high insulation, and thermal protection, and low cost of maintenance. Besides, they have a more stylish look than their wooden counterparts. But besides the advantages, there are also disadvantages. One of such disadvantages are the complexity and, in some cases, the inability to eliminate the scratches on the plastic Windows.
How to fix scratches on plastic Windows
You will need
  • - wooden block;
  • - flannel;
  • - liquid plastic Cosmofen;
  • the solvent 646;
  • - a marker for plastic Windows.
Instruction
1
Wash thoroughly the surface with a wet sponge, without the use of detergents because they may destroy the structure of plastic. Well and then wipe dry the window. Put the gloves on. Repair small and shallow scratches by using a soft fabric for example flannel. To do this, fabricate a makeshift cushion for sanding. Take a wooden bar length of 15 cm. To it attach a few layers of soft cloth or cotton to make a layer it is necessary that in the future not to cause further harm to the window. The basis of the secure flap non-coarse fabric. Take received a homemade cushion and grind a scratch on the window.
2
Take the liquid plastic, for example, Cosmofen, and put them over deep and large scratches. The tool can be purchased in companies that sell accessories for plastic Windows. He should be treated with caution, as the solution contains acetone. Take the flap of rough cloth, put on it slightly and wipe the window surface in a circular motion until you achieve the desired result. Then wipe the plastic clean and dry cloth. After work, they must be disposed of.
3
Prepare the solvent 646 and remove deep scratches. Take a wet rag and a piece of cotton wool. Lightly dampen a swab with solvent. Lightly wipe the scratch. As only slightly dissolve the plastic, immediately wipe it with a damp cloth so that the solvent is not corroded more plastic than required. Repeat these steps until you achieve the desired result. As the solvent is strong enough, first practice on a regular piece of plastic.
4
Take the special token and remove scratches with laminate Windows (with glued film "under the tree"). Purchase it from sellers of accessories for plastic Windows. Pick up the token of the right color. Clean the surface and throughout the length of the scratch in one motion paint.

Advice 5: How to fix a leak in the gas tank

The occurrence of leaks in the tank – common issue, so every driver should know how to rectify it. To repair the tank immediately after detection of the leak without spending time searching for solutions.
How to fix a leak in the gas tank
Instruction
1
If formed in the gas tank hole is small and you do not intend to pour gasoline, then the first thing to stop flowing. Easier and faster all it can be done, carefully smeared the hole with bar soap. Next you need to gently remove excess soap using a cleaner. Be careful, because if you remove too much soap, the leak reopens. Degrease the surface. As degreasers you can use acetone or any other solvent. The degreased surface should be cleaned with emery paper and then leave to dry. Next you need to carefully cover up the hole cold welding and wait 10-15 minutes until the weld will not harden completely. Then soak a few rags with epoxy glue and carefully attach to the surface of the fuel tank by closing the flow. Wait 24 hours and then can re-use the machine.
2
Another way is suitable if the hole is comparatively large. Drain the gas tank of all gasoline, degrease, clean with sandpaper and dry the surface formed near the gas tank hole. Take some rags and soak them with glue. When the glue dries a bit, glue the cloth to the surface of the fuel tank by closing the flow and wait until the glue dries completely. Then apply two layers of glue on the cloth (the thickness of each layer should be about 1-2 cm). Thoroughly cover the patch of nitro and wait for it to dry. Then you can re-fill the petrol tank: a leak is likely to be eliminated.
3
If you don't have time to prepare the surface of the tank (cleaning, degreasing, etc.) – cut from paronite washer, then install in the formed in the tank hole screw and washer, and then cover the surface of the fuel tank paint. Perhaps the hole will first have to increase in order to close it with the screw, but the leak will be immediately eliminated.

Advice 6: How to fix the leak in the aquarium

The reasons for the leakage of the tank can be several: initially admitted the marriage in the production or insufficient aquarium seams filled with sealant. Impractical people can change the aquarium to a new one. But if you are willing to throw money to the wind, then there are several ways that will help you to fix the leak.
How to fix the leak in the aquarium
You will need
  • - silicone sealant for aquariums,
  • - nail file.
Instruction
1
The first thing you need to clean the seams in the leaks, in this case, you will have to move all the fish at a time into another container and drain the water from the aquarium. Remove all the fixtures, the ground and plants, thoroughly wash the aquarium and dry.
2
Now we can start to address this problem. Carefully inspect the seams, they are filled with a special material – sealant, which over time loses its unique adhesive quality, and then breaking the connections, respectively, the aquarium begins to leak.
3
Take a small sharp object, it can be a metal nail file or small spatula, and gently clean from the sodden seam sealer. Proceed very carefully so as not to accidentally damage the glass. Clean absolutely all the rubber parts of the substance that the seam remained almost clean. Of course the work is not easy, but after a thorough cleaning you will only need to seal the inner joints with silicone sealant specifically designed for aquarium. It is perfectly cope with the task.
4
Apply a small amount of sealant on the internal seam and try it wet and soapy finger pushed as deep as possible inside the joints. Try to do it so that the seam was completely filled with sealant, let it is a little better than he will be missed. With a nail file smooth out the silicone and spread the excess on the surface. After all the seams are sealed, leave the aquarium to dry for two days. After the allotted time, fill it with water and see the fruits of your labors. If the leak is not there – then you did the right thing.
Useful advice
Before you apply the sealant, it is advisable to degrease the surface with alcohol or acetone.
Search
Is the advice useful?