You will need
- - isospan grades A, AM, AS, DM, B, RS, C, FD, FS, FX, D;
- - adhesive tape isospan KL and SL;
- stapler;
- construction tool;
- construction fasteners;
- - wooden slats 40-50 mm.
Instruction
1
The use of film isospan for external insulation of buildings
For exterior insulation of roofs and facades of buildings there is a need to provide protection from moisture and wind, while retaining the possibility of evaporation of water vapor from the insulation. For such cases, use "Izospan" brands AND, AM, AS, provide moisture and wind protection with the preservation of water vapor.
Lay film on the heater white side to him. Laying perform bottom-up horizontal stripes overlap providing overlapping joints of at least 15 cm For fastening protectors to a wooden obreshetku or rafters, use a stapler. Glue joints adhesive tape isospan KL or SL.
For exterior insulation of roofs and facades of buildings there is a need to provide protection from moisture and wind, while retaining the possibility of evaporation of water vapor from the insulation. For such cases, use "Izospan" brands AND, AM, AS, provide moisture and wind protection with the preservation of water vapor.
Lay film on the heater white side to him. Laying perform bottom-up horizontal stripes overlap providing overlapping joints of at least 15 cm For fastening protectors to a wooden obreshetku or rafters, use a stapler. Glue joints adhesive tape isospan KL or SL.
2
On top of the film came to obreshetku or frame spacer rails with a size of 40-50 mm. They need to ensure the gap between the membrane and the outer coating (exterior panels or roofing material).
3
Isospan brands DM and is mainly intended for installation under metal roofing, for example, sheet metal. In this case, unlike the above-described technologies is that the film is placed on a heater with a clearance through a spacer slats.
Before laying the film fasten to the rafters spacer rails with a size of 40x50 mm. Lay them on a membrane with tension (so that it does not touch the insulation) and secure the strips with a stapler. Styling make horizontal stripes from the bottom up on the roofing with an overlap of not less than 150 mm. Seal the joints with tape isospan KL or SL.
Before laying the film fasten to the rafters spacer rails with a size of 40x50 mm. Lay them on a membrane with tension (so that it does not touch the insulation) and secure the strips with a stapler. Styling make horizontal stripes from the bottom up on the roofing with an overlap of not less than 150 mm. Seal the joints with tape isospan KL or SL.
4
Nail to spacer rails another series of rails. Attach them to the crate and lay roofing material. Thus, the membrane with two sides is a gap, which allows good ventilation of the roof.
5
The use of membrane "Izospan" in the insulation structures inside
To provide a vapor barrier with insulation of walls and roof from the inside, apply isospan brands, RS, C, DM.
Lay the film with the smooth side against the insulation (rough out) horizontal stripes from the bottom up. Provide overlap joints of at least 15 cm (material brand FX down back). Glue joints adhesive tape, preferably of the brand "Izospan" FL (FX material for application of the tape FL is mandatory). Fixing the foil to the rafters or wooden obreshetku make stapler.
To provide a vapor barrier with insulation of walls and roof from the inside, apply isospan brands, RS, C, DM.
Lay the film with the smooth side against the insulation (rough out) horizontal stripes from the bottom up. Provide overlap joints of at least 15 cm (material brand FX down back). Glue joints adhesive tape, preferably of the brand "Izospan" FL (FX material for application of the tape FL is mandatory). Fixing the foil to the rafters or wooden obreshetku make stapler.
6
Fasten to obreshetku over the membrane vertical counter-batten sizes of 40-50 mm. They need to create a gap between the membrane and the inner lining. Kontrakan fasten to facing material (drywall, paneling, etc.).
7
The use of reflective materials isospan
For the device warm floors or thermal insulation of walls and roofs from the inside there is a necessity simultaneously with the provision of hydro - and vapor barrier to prevent the departure of heat out. In these cases, you should use "Izospan" marks FD, FS, FX.
Before laying the heating elements warm the floor lay film reflective (metallic) surface up. Provide overlapping not less than 150 mm (material FX down back). Glue joints adhesive tape (isospan FL). Lay the membrane over the heating elements.
For the device warm floors or thermal insulation of walls and roofs from the inside there is a necessity simultaneously with the provision of hydro - and vapor barrier to prevent the departure of heat out. In these cases, you should use "Izospan" marks FD, FS, FX.
Before laying the heating elements warm the floor lay film reflective (metallic) surface up. Provide overlapping not less than 150 mm (material FX down back). Glue joints adhesive tape (isospan FL). Lay the membrane over the heating elements.
8
When working with vertical or inclined surfaces engage the laying of reflective film, horizontal stripes from the bottom up with standard (150 mm) overlap joints. Glue the joints with adhesive tape.
9
When laying the material interior finish (gypsum Board, paneling, etc.) provide with the help of spacer strips clearance of 4-5 cm between it and the reflective membrane. Necessary to achieve a high reflection effect of heat.