Advice 1: How to disassemble sony vaio pcg

Sometimes the laptop must be disassembled to clean or to upgrade. However, information on dismantling the producers are only specialized services for repair of computer equipment. Anyway, to disassemble the laptop at home. Only need to do this carefully.
How to disassemble sony vaio pcg
You will need
  • - Screwdriver
Instruction
1
When disassembling the netbook Sony Vaio, you must first remove the battery. To do this, pull the corresponding lock on the bottom side of the device and remove the battery.
2
Unscrew all the bolts from the lower base unit, including under the rubber plugs. Remove the corresponding part of the body, which will be disconnected after removal of the bolts.
3
Remove the plastic cover from the left hinge using a thin screwdriver, releasing an internal latch.
4
Next, start to remove the keyboard, pulling the top panel slowly over. Pull it up until the keyboard is fully disconnected from the base. Do not rush to remove it, first disconnect the cable from the motherboard memory.
5
In part of the body, which is closer to the touchpad, there is a slot for RAM. Remove unnecessary bar and replace it. Insert the new strap into the corresponding slot. To pull the RAM, gently press the slot, then bend it at the angle approximately equal to 45 degrees. Release the corresponding latch. You can then carry out the replacement.
6
To remove the hard drive, disconnect the card with USB ports and SD. Its held by two screws that you must Unscrew with a thin screwdriver.
7
Loosen the screw which secures the metal plate of the hard disk. Lift the hard drive, disconnect the ribbon cable. To do this, pry up the connector, and pull out the cable.
8
After the upgrade and cleaning assemble the device in reverse order.
Note
Disassembly of the netbook and all the accessories is at your own risk. Any damage caused in the process of disassembly is not covered by warranty. Also, the warranty is void if housing opened by the user.
Useful advice
Before disassembly remove the laptop all devices, in particular SD card.

Advice 2: How to disassemble a hard drive

Venturing on the hard disk, many users-beginners do not understand that you can do with the disc, if it's open at home. When assembling the hard disk in the production of inside the box creates a vacuum that allows it to run for a long time. Hard drive becomes unusable after a few seconds of interaction with air. Experienced users of the personal computer apart the housing of the hard drive only with the full confidence of the non-working state of the hard disk.
How to disassemble a hard drive
You will need
  • Hard drive screwdriver "+", hexagon.
Instruction
1
Disassembly hard disk start with the dismantling of control boards. Control Board – this is a common circuit Board on which is soldered a set of parts, including modern memory chips. Depending on the kind of hard disk, for Dismounting, you will need either a screwdriver or a hexagon. Remove 3 screws, then remove the control Board of the hard disk.
2
Under the control Board cover is the hard drive, which is all the device hard disk, which you probably have seen many times in photos made by other users broken hard drives. Remove 7 screws, then remove cover of the hard disk. The major task of dismantling the hard drive is finished. If you dismantle a hard disk for parts that are inside, then follow on.
3
All other parts: filter, head and discs can be disassembled with a screwdriver. Be careful during the parsing mechanism of the heads of the hard disk – they are equipped with powerful magnets, you can pinch your finger. Once you remove the "pancakes" hard disk, will be able to ensure that their surface is easily scratched with any object. The number of heads in a hard disk in two times more than the number of "pancakes". Therefore, if your hard drive had 4 "pancake", hence the number of heads is equal to 8.

Advice 3: How to disassemble laptop keyboard

Many of us like to eat in front of the computer, or drink coffee, juice, Cola and other drinks. Unfortunately, this bad habit often leads to tragedy - one wrong move, and the mouse/keyboard we can safely take to the dump. But what to do if a victim of your carelessness was the keyboard of the laptopand? Its not just going to throw it out or change to a new one for 200-300 rubles. In the event of various incidents, and just to prevent you need to know how versed the keyboard of the laptop.
How to disassemble laptop keyboard
Instruction
1
To disassemble the keyboard we have in different occasions. For example, it may have gotten clogged and some keys started unpleasantly sticky. Or you filled the keyboard with something sticky, and you need to clean the contacts. So first of all you need to turn off the laptop and remove its battery. Each button on the laptop is secured by a special mechanism, called microsoftie. Buttons of different functionality have different mounts, so when removing the plastic part is better to postpone together with the mount.
2
Start to disassemble the keyboard of a laptop with the letters on the keyboard. First, you you just flip the plastic button and see before you two mounts. To remove them you can use a dental probe and tweezers. Mounting must be otmachivat top, where the lifter is fixed vertically. Side mounts are more fragile, so when removing, you can damage the side lugs. In any case, do not try to remove all microsofty at the same time, it is better to spend more time, but to do it qualitatively.
3
As soon as the letter keys will be finished, you can move the buttons with mounts of a different type. Buttons PgUp and PgDn, the cursor and the button E is kept white and black mounts. Removing the plastic key, you will see a white mount. You need to bring the lugs from the hooks, which are located on the left at the top and bottom. The button and the Shift button are removed in a similar way, except that buttons are blank two lifter instead of one. Then you can proceed to the buttons of the last group. This button is alt, fn, ctrl, and win. You draw from the hooks of the lugs, which are located on the right top and bottom.
4
As soon as all the buttons on the keypad will be on the table, you will need to remove the black stencil, where each button corresponds to a triangular rubber band. Below it is film based. On this three-layer basis and are pads that closes when the liquid enters them. To act for this step very carefully, as the layers of film bases are very fragile and easily torn. If you have no experience with such delicate mechanisms, we recommend that you give laptop repair in specialized service.

Advice 4: How to disassemble laptop battery

The normal laptop user is not so often have to disassemble its computer equipment, as service centers in our country are quite common. But still turn to the master for repairing, in particular, the battery from the laptop, sometimes not entirely justified because of the high cost of this service (in comparison with buying a new battery).
How to disassemble laptop battery
You will need
  • - a knife or screwdriver;
  • - hammer;
  • vise;
  • - multimeter;
  • - soldering iron;
  • - spare battery cells;
  • - automobile light bulb;
  • fabric gloves;
  • glue.
Instruction
1
Pick up the necessary tools, which will, in the future, disassemble. The minimum set includes a sharp object - this can be a knife, an ordinary kitchen or stationery) or a screwdriver. And also, a hammer to facilitate the process of disassembling the battery, grip for anchoring parsed object stationary and fabric gloves - they help you to avoid getting skin oil on the elements and protect against mechanical damage of the hands understand.
2
Secure the battery latch. The two parts of the battery glued together at the seam, which is located right in the middle of its lateral parts. Insert a sharp object under the angle of 45 degrees. Start by lightly tapping the handle with a hammer or hand. Because the plastic is soft enough, the seam will disperse, but if at some point the glue will hold very tightly, this part should be notched.
3
Inspect the battery cells. Usually laptops use them six or eight parts. If there's no sign of mechanical damage to the elements, as well as batteries are not "flowed", you can try to replace the old elements with the new, previously bought from an online store or in the shop radio. For battery replacement, you will also need a multimeter and a soldering iron.
4
Check with a multimeter each element. Each battery should give a value of approximately from 3.7 to 4.1 V. Discharge elements is necessary in order to later all the items were charged uniformly. For this fit automotive light bulb. After the discharge of all battery cells, connect them with the fixtures. The last lock together using a soldering iron. Connect of the battery and glue the seam to prevent moisture from getting inside. Insert the battery in the laptop and make a few full cycles of charge-discharge.

Advice 5: How to disassemble the netbook Acer Aspire One

The most difficult and responsible operation when disassembling the netbook Acer Aspire One is disconnecting the cables from the motherboard. Be extremely careful when doing it. The latch is fragile and small and can not be recovered. Damaging the latch, you will not be able to connect to the motherboard of the device and in fact the computer will become worthless and all further recovery through a service center.
Disassemble Acer Aspire One
You will need
  • - netbook Acer Aspire One;
  • - screwdriver set.
Instruction
1
The first thing de-energizes netbook Acer Aspire One. This is necessary in order not to accidentally burn the motherboard.
Pull out the power cord and take out the battery of the netbook. For removing the battery you need to push the two latches on both sides of the case and pull the battery from the housing to the outside.
Next, remove the 3 bottom cover that covers the connectors for the hard drive, RAM, and additional room for expansion Board, unscrewing the shown on photo 4 screw.
Take out the battery of the netbook Acer Aspire One
2
Unscrew from the bottom of the netbook Acer Aspire One all the screws. There should be 7 on the housing 3 in the battery compartment and 1 compartment for RAM.
In order to remove the hard drive, Unscrew 1 screw and pull the drive from the connector, and then up on yourself.
Unscrew the screws from the bottom Acer Aspire One
3
Remove keyboard netbook Acer Aspire One. It is fastened with plastic latches around the perimeter. From the keyboard, gently prying it with something sharp and moving around the perimeter, separate the keyboard from the case.
Under the keyboard, naturally, is the ribbon cable of the touchpad and led indicators. Disconnect it by pulling the little plastic latch in the direction from the connector, and then pull the ribbon cable out of its connector. Be extremely careful when releasing the plume, because the latch is very fragile and small and can not be recovered.
Remove keyboard netbook Acer Aspire One
4
After you have removed the keyboard netbook Acer Aspire One, need to disconnect from the motherboard two loop, marked in the photo, in the same way. Observe extreme accuracy when performing this operation.
Disable the plumes netbook Acer Aspire One
5
Unscrew all the screws marked on the photo, located under the removed keyboard.
We release the top cover of the netbook Acer Aspire One
6
You can now remove the top cover of the netbook Acer Aspire One. Have full access to the motherboard, the CPU, cooler, speakers, power connector, etc.
Remove the top cover of the netbook Acer Aspire One

Advice 6: How to disassemble netbook Sony Vaio PCG-21311V (VPCM12M1R)

Parse netbook Sony Vaio, model PCG-21311V (VPCM12M1R) to replace the RAM module and hard disk.
Netbook Sony Vaio PCG-21311V (VPCM12M1R)
You will need
  • - a netbook Sony Vaio model PCG-21311V (VPCM12M1R);
  • - screwdriver set.
Instruction
1
Turn netbook Sony Vaio PCG-21311V (VPCM12M1R) up the bottom. Detachable battery.
Now Unscrew the 6 screws indicated in the photograph. The screws numbered 1 and 2 hold the keyboard, and number 3 secures the hard disk. One of the screws that secures the keyboard also locks and slide the hard disk.
Please note that the screws are in position number 2 is initially sealed with black adhesive tape. Tape almost the same color as the body and almost not visible. To Unscrew these screws, you will have to remove the tape.
Unscrew the screws on the bottom of the netbook Sony Vaio PCG-21311V
2
A slot with a module of RAM is at the top of the netbook Sony Vaio VPCM12M1R, under the keyboard. This netbook has only one slot.
Turn over the netbook keyboard up. The mounting screws of the keyboard we have already unscrewed, left, neatly podawa keyboard on the perimeter and pulling the plastic clips out of the keyway, a little to pull her out of the recesses on the top panel. Raise the keyboard without disconnecting the ribbon cable from the connector. After that, the slot of RAM becomes available, and you can replace the memory modules higher capacity or faster.
Replacement RAM memory netbook Sony Vaio VPCM12M1R
3
To remove the hard drive netbook Sony Vaio PCG-21311V turn the computer bottom up. The battery compartment acts as a metal loop slide the hard disk. Pull in the direction from the center, and the HDD comes out.
Take out the hard drive netbook Sony Vaio PCG-21311V (VPCM12M1R)
4
If you need to disassemble the netbook completely, then remove remaining screws from the bottom of the hull. Disconnect the keyboard ribbon cable and remove it. Disconnect the 2 black wires, located under the keyboard and going to the wireless network card. Then carefully walk around the perimeter and remove all the plastic clips connecting the upper and lower lid. And then detach the top cover from the bottom of the netbook to get to the motherboard.
Is the advice useful?
Search