Advice 1: How to mount sheet panels

Leaf panel – material for decoration, popular. It is reminiscent of plywood covered with a decorative shell. The variety of designs allows you to transform any interior - finish wood to create the illusion of a natural mosaic, or find other creative solutions. Repairs can be finished rather quickly, however, you must carefully study the characteristics of the material and securely fix it on walls or ceilings.
How to mount sheet panels
You will need
  • - leaf panel.
  • - emery;
  • - soap and clean water;
  • - dusters;
  • - putty;
  • - hacksaw or a circular saw;
  • - hammer;
  • - glue panels;
  • - brush and a spatula;
  • - nails (screws, staple gun);
  • - crate;
  • - silicone sealant;
  • - wooden support;
  • profiles and other accompanying decorative material;
  • - personal protective equipment.
Instruction
1
Explore information on modern cladding panels. Their base can serve as plasterboard, hardboard or fiberboard MDF, PVC and some other materials. Each has its own characteristics, reacts differently to humidity and temperature changes. Be sure to consult with the sellers stores building materials and craftsmen in the decoration of apartments. Only after this you can choose the best panels for your premises and not be afraid for the quality of the repair.
2
Soak the selected finishing material a few days in the room where are going to mount them to the walls or ceiling. Sheet panels need to acclimatise to the level of humidity of the ambient air and the building materials close to each other.
3
Perform preliminary measurements of the surface of the walls (ceilings), consider all the pitfalls (uneven floors, sockets, radiators, etc.). Leave a gap for a possible expansion of the wall panels; the height of each blank must be inch less than the distance from floor to ceiling.
4
Cut the cloth the size you want. When using a hacksaw is recommended to make cuts from decorative coatings; when working with a circular saw is better to make the workpiece from the base.
5
Prepare walls (ceilings) to finish sheet panels. They need to be thoroughly cleaned of all dirt and allow to dry. Remove the remains of the old decorative covering – Wallpaper, paint material. The bumps align with a good quality putty suitable for the type of surface. At the end of the walk on walls or ceilings with sandpaper.
6
Start to mount the panels. If a finished surface is quite smooth (and the room is dry or moderately wet) the leaves can be glued using a special acrylic, neutral silicone, or a universal construction adhesive. Read the instructions on the detergent and just keep all the advice of the manufacturer.
7
Gluing wall panels should be first on the inner corner of the room, then around the perimeter. Need not closely joined sheets between the desired gap of approximately a few millimeters. You then fill with silicone sealant. The same small cracks at the joints place material from Windows, doors, corners.
8
Apply adhesive on the entire surface of the base of the finishing material. Plastic profiles suitable color fill with sealant and install on the edges of each sheet. After that panel needs force to press against the wall and carefully rattle with a hammer so that the glue grabbed better.
9
Put glued to a sheet of temporary support of wood, to better consolidate the material. There will be only wipe up excess sealer with a clean cloth and, if necessary, to further strengthen the sheets with screws or nails.
10
If you have to make repairs in a room with uneven walls, it is recommended to install the panels on the crate. Attach with screws to the surface of the wood that they were at a distance of about 0.5 m from each other. After this decorative material can be fixed construction stapler or other fasteners.
Note
If the panels are installed without plastic profiles, be sure to let the glue dry, as it is able to change the color of silicone sealant.
Useful advice
To disguise some of the shortcomings of cladding (such as nail heads or rough joints) by using special inserts. They are available in stores bundled with the main building material. In the same style sheet panels you can pick up a whole system of interior decoration, which will include many elements - from the corners, cornices, skirting boards to halogen lamps.

Advice 2: How to mount panels in the kitchen

A lot of people engaged in the installation of panels on the kitchen. It is worth noting, it is rather complicated and it must be approached with a particular mindset. Most often questions arise with the mounting panel for the apron. The panel for the apron is a large rectangular sheet of laminated chipboard, which have a smaller thickness than the countertop.
How to mount panels in the kitchen
Instruction
1
For "apron" would be the best plate, which has a thickness of from 3 to 10 millimeters. It must be covered with tape the same color. If the table has a pattern on the tile he, too, must be present. This "apron" can be quickly mounted. One of the advantages also worth noting is its reasonable cost. To mount a wall panel in the kitchen area apron is quite simple.
2
First you need to secure the wall panel to the wall in the right place. For this purpose, suitable liquid nails. Quite often, panels are mounted on the dowel-nails or 6x60 6х40 to the wall. You can then close the decorative caps-plugs in the color panel. The top edge can be easily removed under the top shelf. The lower edge of the wall panel to strengthen the skirting Board, it is called the parietal side. Wall skirting must be secured to the countertop using screws. In the end, the wall panel is securely fastened.
3
The color of the area should be similar to the color of the superposed panels. Also the corners look good in silver and Golden color. They will combine with the color of the handles of the kitchen or the roof rails. Using the area you can hide the connecting seam between the panels. He also will not allow the crumbs to fall under kitchen tables. Best for kitchen use the rails as they help to further secure the panels to the wall.
4
There is another way. If the wall on which you plan to mount the panel, smooth the panel to put at the top of the headset. In the end, on top of it is pressed against the drawers, and the bottom will be fixed to the baseboard. The upper cabinets of the kitchen units should go to the bar, about 2 cm. No need to glue. In the case of the dismantling of don't have the panel to detach from the wall.

Advice 3: How to glue panels to the ceiling

Ceiling panels made of polystyrene foam use enough great demand. And this is understandable. A relatively small price, attractive appearance and easy installation make ceiling panels are a popular decorative material, widely used in the repair. Installing ceiling tiles requires no special skills or tools and can be carried out independently.
How to glue panels to the ceiling
You will need
  • a ceiling panel;
  • glue;
  • construction knife;
  • - sheet of corrugated cardboard;
  • ladder;
  • the pistol sealant;
  • - roller;
  • brush;
  • - primer;
  • - ropes;
  • - the range;
  • - sponge;
  • - a wooden beam;
  • ceiling plinth.
Instruction
1
Perform the necessary measurements and make a drawing respecting the aspect ratio. Consider the location of the panels on the ceiling and calculate their required number. It is very important to determine the position of the tiles with a precision of a few millimeters.
2
Before buying, inspect the tile. The panels should be smooth and have the same density throughout the area. The presence of "holes" is considered a serious defect. The edges should not crumble. The corners of the tiles should be straight and not jammed. To buy panel recommended stock 4-6 pieces.
3
Select glue. To paste the tiles as possible, you can use "liquid nails". But if you want to stick the tiles so that if necessary it was possible to remove and use elsewhere, it is recommended to use special mastic for ceiling cover or glue for polystyrene.
4
Prepare the ceiling surface. If the ceiling had been whitewashed, you must thoroughly wash off all the plaster - the remains of chalk or lime will lead to the fact that the tiles will come unstuck. Carefully programsuite the ceiling with a roller and brush. Allow primer to dry. If necessary zashpaklyuyte cracks and crevices. The surface should be smooth, dry and free of grease.
5
Make the necessary markup. To do this, define the center of the ceiling. Pull the two ropes diagonally, the point of intersection will be the required center. Swipe through this point two centerline. Mark the location of the panels and verify that the "wall" series are of the same width.
6
Apply glue to the center and in the corners of the tiles. Position it on the ceiling so that one of its corners was strictly in the planned centre. Firmly press it to the ceiling using a piece of wood of suitable length. This will allow you to avoid dents. Remove excess adhesive with a damp sponge.
7
Attach the remaining panels in parallel rows, putting them close to each other. Focus on the previously made markings. To cut the tiles, it is recommended to prepared sheet of corrugated cardboard using a sharp construction knife.
8
Take the ceiling tiles. Apply glue to the adjoining wall and ceiling surfaces, and carefully apply around the perimeter of the room. In order to connect to the throat in the corner, you can use special corner pieces or just trim the ends at an angle of 45 degrees.

Advice 4: How to attach wall plastic panels

Decorating a room or kitchen wall plastic panels gives the room a nice look. This coating is practical and convenient in daily maintenance. Installation of plastic panels does not require laborious preparation and leveling of the walls. Despite this, the material is trimmed so the walls look like, as a rule, perfectly.
How to attach wall plastic panels
You will need
  • - wall plastic panels;
  • - wooden bars;
  • - nails or screws;
  • - hammer;
  • - screwdriver;
  • knife;
  • - plumb
  • - building level.
Instruction
1
The installation of wall panels, start with the installation of fastening elements. On the surface of the wall, attach the dry wood that they reside perpendicular to the direction of installation of the panels. Use to set bricks level and building level. The optimal distance between the bars on the wall shall not be more than 400 mm.
2
Make sure wall panel is precisely cut according to the height of the walls of the room. Insert the first plastic panel into the groove of the fastener by a narrow shelf. The panel must be positioned very exactly relative to the angle of the wall surface. Wide mounting shelf, fasten to bruskam nails or screws.
3
The second wall panel insert in the first slot. Making sure that between the panels with no gaps, secure the panel with the selected method. Consistently connect all of the remaining panelsto cover the entire surface of the wall.
4
The last panel reduce in the longitudinal direction from the wide mounting of the shelf relative to the center of the fastener about 5-7 mm. First, insert the wall panel into the groove of the fastener, and then tightly attach to the previous panels. Additionally, attach the last panel is unnecessary.
5
If you want to cover the walls in combinations of various colors, use for joining panels of a special connecting element.
6
For mounting on the surface of the panelled walls, lamps or other devices, install an additional obreshetku from wooden bruskov in areas proposed mount before the installation of the panels.
7
Go to mount panels on the next wall, observing the above sequence of operations. Finish with the plastic panels of the walls, attach bottom skirting boards, and to the junction of wall and ceiling – of the throat.

Advice 5: Fire-resistant wall panels: pros and cons

In recent years, a variety of finishing materials allow one to avoid such a long and labor-intensive kind of work, as the alignment of the walls. Fire resistant decorative plastic panels save time and money, solving the problem of internal finishes. Most often, they are used during the finishing works in buildings and premises of the business, social and public purpose, but there is no reason to abandon their use in apartments and private homes.
Fire-resistant wall panels: pros and cons

What is fire-resistant panels and where they are used



These panels are made of polyvinyl chloride having ability-extinguishing. Typically, this patterned strips having a width of from 10 to 30 cm and a thickness of about 1 cm. their Length can vary from 2.5 to 6 m. Surface can be glossy, matte or textured, organic dyes, it is applied to any picture printing method. This drawing is not afraid of moisture and the panels can be washed frequently, however, to use a particularly aggressive chemical cleaners are not recommended.

Fire-resistant wall panels are not only economical, but also environmentally friendly material that can be used for walls in rooms of any purpose. Wall coating made from these panels, possesses high durability and decorative qualities, allowing to realize any design decisions, giving the interiors not only originality, but also comfort – in appearance, they can mimic the traditional in the design of natural materials.

They have fire-retardant, safe and easy to wash, so they have found application in medical and care institutions, shopping malls, stores, warehouses, offices, various non-residential and residential premises. But still there is a prejudice against this synthetic finishing material, plastic is not considered eco-friendly homes its use is confined to the bathroom and bathroom.
Increased durability and strength allow fire resistant panels keep its properties and appearance.

The advantages and disadvantages of fire resistant wall panels


PVC, which is made of fire-resistant panels used for making many things that you use every day. This material is made of linoleum, water pipes and even plastic bottles used as containers for drinks, and this is evidence of its environmental safety.
With plastic wall panels you can easily hide engineering communications, leaving open the possibility of quick and easy access to them.


This non-combustible facing material is not afraid of moisture and not subject to the destructive action of putrefactive bacteria on it will not start any fungus or mold. Wall and ceiling panels are easily and quickly installed, and you do not need to align the walls and ceiling. And, most importantly, they are absolutely safe against fire, because have the ability to self-extinguishing, fire resistant and even at high temperatures only slowly smolder, not ignited. By the way, and low temperatures, they are also not afraid, so they can be installed in unheated areas, including balconies, verandahs, gazebos.

The disadvantages can be attributed only to the possibility of deformation under prolonged exposure to a powerful source of heat. Therefore, to install the heaters adjacent to the walls, feature panels, is not recommended.
Is the advice useful?
Search