Advice 1: How to disassemble binoculars

Binoculars is the constant companion of hunters, soldiers, travelers and tourists. Low-power devices are used in theatres and circuses, and particularly strong in astronomical research. However, this device is quite fragile to break it easily. While inside the structure may get dirt, sand or water, and the position of the parts to be violated. In this case, it is necessary to disassemble the binoculars and brush it.
How to disassemble binoculars
You will need
  • Cans of compressed air "Dust Off", soft, lint-free special cleaning liquid and a small screwdriver, including sentinels.
Instruction
1
To start, determine what type of binoculars belongs to your model. There are two types of these devices: classic compact Porro and Roof. Note that they have different structure. Based on these data, read the relevant literature or consult with a specialist. The easiest way to learn about the sequence of disassembly of the binoculars is to read the instructions.
2
Many modern binoculars are filled with nitrogen inside. This is done to avoid fogging of the prisms and lenses due to temperature changes. That is, when the opening of the case you can release nitrogen. So once again weigh the "pros" and "cons" – whether disassembly is required?
3
Prepare the workspace. It would be better if the table surface is closed with a soft cloth. Start to disassemble the binoculars. Unscrew the tiny screws on the body, they can be covered and therefore completely invisible.
4
Disconnect the tube with lenses and remove closing cap. Gently loosen the prism from the clips. In the process of dismantling details memorize the structure of the binoculars. If possible – keep before the eyes of the user manual with the scheme. When detaching the parts, wipe them with a cloth dampened with cleaning fluid. However, the lenses and prisms before that process the air from the cans of "Dust Off" to blow away the dust. If from the beginning to use cloth, dust will leave microscopic scratches.
5
In the same sequence collect the binoculars back. Of course, all this is General advice. Binoculars very much, and each model requires an individual approach to disassembly. And if you are not confident in their abilities, it is best to take the device in the optical workshop.

Advice 2 : How to set binoculars

Binoculars can rightly be called the most popular of the Supervisory device, as they provide a good the information content of the observations and does not tire the eyesight, due to the fact that you are using both eyes. For optimal observation you need to bring a pair of binoculars in accordance with the individual characteristics of your eyes and vision.
How to set binoculars
Instruction
1
Begin customizing your binoculars with setting his interpupillary distance for this view in binoculars to a distant object and try to move and push the binoculars until, until you see a clear image, you should see a full circle.
2
Vision your eyes may slightly differ from each other, so a pair of binoculars requires diopter setting and focus. On the right eyepiece is usually a ring diopter setting to resolve differences of images, and the left eyepiece does not adjust – it is stationary.
3
Watching the remote object in binoculars, close right eye and turn the head of the Central focus until the complete definition of the image of the object. Then close left eye and look at an object in the right eyepiece, do the same to set the sharpness of the image to the right eyepiece, rotate the diopter setting ring. Ready – binoculars and focused in the future, you need only head the Central focus. If the settings are wrong, you can correct them or reconfigure binoculars with notes plus/minus.
4
If you need to change magnification, rotate the lever to change the zoom on the binoculars to the desired values, and then turn the Central focusing ring until you get the definition. Keep in mind that every time you change magnification, you may need to adjust the focus.
5
If you are setting up a pair of binoculars with variable magnification, to focus it better on full zoom, this will reduce the need to further adjust the focus each time when changing magnification. In order to focus on a closer object, focus first on the furthest possible and then decrease the magnification of the binoculars. Generally, binoculars with variable magnification image better and clearer at a close distance.

Advice 3 : How to disassemble laptop Samsung R60

From time to time it is necessary to clean the computers and laptops from dust and dirt that had accumulated inside of them, clean the keyboard from falling back cookies or just to change the configuration. Disassembly of many models of laptops are different.
How to disassemble laptop Samsung R60
You will need
  • - screwdriver;
  • - Unsharp knife.
Instruction
1
Unplug the laptop from power source, remove the battery and disconnect the power cables. Unscrew all fasteners from the rear wall of the housing.
2
Remove the lid from the division of the hard disk, it is there the biggest. Pry it with your fingers or not sharp knife, being careful not to damage the surface. Unscrew the mounting of the hard drive, remove it by disconnecting the wires.
3
Similarly remove the drive. You would have to be especially careful. Underneath will be another fastening element. Unscrew it. Remove the memory modules (this is not necessary), open the Wi-Fi antenna.
4
Turn the laptop monitor up, remove the bolts from the panel above the keyboard. Gently pry it until it snaps fastening. Be careful this is very fragile item. Then turn the laptop back on. Gently remove the keyboard. Disassemble it completely on the buttons is not recommended, as the inside contains small, fragile items that are very easy to break or lose.
5
Remove the keypad included using the Unsharp knives, in the same way otdelnie clamps from the battery compartment, of which there are only 4. Turn the laptop back on.
6
Remove the panel, which was located under the keyboard, to do this, pry it a little with a screwdriver and otdelnie clips. You will discover two hidden fastener, Unscrew them. Carefully disconnect the touchpad, speakers and screen, be especially careful with wires and cables of devices – many of them then it will be hard to get.
7
Again, flip the laptop back cover up, otdelnie the main panel, remove the cooler and clean the computer from dirt and dust, use a vacuum cleaner or other convenient means. Assembly takes place in reverse order.
Note
Read the warranty terms and conditions – usually, disassembly of the computer deprives you of the obligations of the seller and the manufacturer of the repair or replacement of the product.
Useful advice
Produce disassembly of the laptop on carpeted surfaces so as not to lose small parts.

Advice 4 : How to disassemble the computer chair

If your computer chair is broken, and you decided to try to fix it yourself, then the first problem you may face is the order of its disassembly. To disassemble and repair the computer chair is not difficult if you know some of the nuances. The repair is quite possible to produce with their hands.
How to disassemble the computer chair
You will need
  • - flat screwdriver;
  • - rubber hammer;
  • - hammer;
  • - Phillips screwdriver;
  • - circle punch
Instruction
1
Turn over the computer chair up Petrochem and remove the four screws connecting the chair seat mechanism with height adjustment - piastras. Remove the chair seat.
2
Disconnect the gas lift chairs parts from

As in the place of these parts are no threaded connections to bring down the piastre with gas lift, lightly tapping it with a hammer. For this kind of work is recommended to use a rubber mallet to avoid damage and not to bend the piastre. Note that if the chair was in operation for a long period of time, in order to detach these parts can require considerable effort.
3
Remove the base with gaslift

Inspect the gas lift. In the lower part there is a special retaining washer that instantly breaks when you hit it with a hammer. Therefore, in order to disconnect the crossbar from the gas lift necessary to use a special tool - ring punch. Put the d-pad computer chair between the two tables. Install the hole punch. Knock the gas lift from the cross with heavy hammer.
4
Remove the wheels of the chair. To pull them out of nests it is possible hands. If in the course of this operation the metal pin wheel left d-pad of the chair - remove it using pliers.
5
Inspect the d-pad. In its center there is a ring with five lugs, for fixing to plastic casing. Hook and fold the edge of the casing using a flat screwdriver. Slide the cover and lift it off the edge of a ledge. Swipe the same procedure for all 5 casings. Remove the knockout from the metal housing.
Your computer chair is disassembled.

Advice 5 : Mineral wool or polystyrene: pros and cons

The most popular thermal insulation – mineral wool and foam, which is a modification of the "PENOPLEX". These materials are suitable for insulating walls, roofs and floors of any structure.
Mineral wool or polystyrene: pros and cons
Every insulator has its advantages and disadvantages. Over the years the use of mineral wool and foam was determined as the most preferred applications.


Characteristics of mineral wool and foam polystyrene"




Mineral wool is a fibrous material, which is produced in rigid and semi-rigid mats and rolls. This insulator is produced by melting of igneous rocks. Undoubted advantage of this material is that it is not only flammable, but also prevents the spread of fire. Mineral wool is vapor permeable, has a low thermal conductivity, environmentally safe, has good sound quality.


The main disadvantage of this material is that it absorbs moisture. It completely negates a lot of his dignity. Wet insulation can not to a sufficient degree to prevent the penetration of cold, in addition, it moves down, exposing part of the wall. So if you are using mineral wool should be installed high-quality vapor - and waterproofing. This requires additional financial and labor costs.


In addition, the disadvantages of this material include its considerable weight. For the installation of mineral wool requires a much more durable frame than sheet polystyrene and its modifications.


"PENOPLEX - heat insulation of new generation, which is produced in the plates. This material is clear geometric forms, light weight, high thermal insulation properties. To replace the "PENOPLEX 31S" came "PENOPLEX Comfort, which, due to the presence of the g-shaped edges, allows to avoid cold bridges.


Plates of the thermal insulator light in weight that provides ease and speed of installation. In the composition of the material: no harmful substances, so it is safe from the point of view of ecology. If during installation * necessary personal protective equipment as highlighted in fine fibers and dust when you use the "foam polystyrene" this is not required.


Which is better: mineral wool or foam polystyrene"?




If you want to insulate the Foundation, alternatives to the foam no. Mineral wool for these purposes will not work. In other cases, these insulators are almost identical. Installation of mineral wool but more labor intensive and costly. "PENOPLEX" wins not only in speed and ease of installation, but also for several other reasons: it does not absorb moisture, does not require a heavy frame and waterproofing, it can be glued to the wall or mounted on it a plastic dowels.


"PENOPLEX" can be used for insulation of communications, paving, road paving. If the decisive factor in the choice of insulation is not only heat but also sound insulation, are better advised to use mineral wool.
Is the advice useful?
Search