Advice 1: How to lubricate a laptop cooler

With prolonged use of the laptop, dust buildup inside the unit can not be avoided. It may not the best way affect the operation of the cooling system, which subsequently will lead to internal overheating and rapid failure. Moreover, one of the main reasons indiscriminately laptops is the pollution of the coolers.
How to lubricate a laptop cooler
You will need
  • Laptop, special oil cooler, thermoproteaceae pasta
Instruction
1
So, to grease a cooler laptop, you should know the basic principles of analysis laptops. This is important because each model can have its method of Assembly. Read the detailed instructions for your model. Gently loosen the outer screws of the laptop and remove the keyboard panel. Once you get directly to the cooler, disconnect it from the radiator.
2
Before proceeding to the lubricant cooler, you should clean it and the adjacent radiator of the accumulated layer of dust. It is advisable to do a regular vacuum or blow pump. Next, remove the sticker in the Central helical part of the cooler. Below it will be a small hole, closed with a rubber stopper. This hole leads directly to the axis of the motor and its bearing parts.
3
Fill the syringe with some special oil which can be purchased at almost any computer supply store. Taking or pierced with a syringe tube, slowly push the oil inside. In any case, do not inject it – to allow the oil to flow along the axis in the bearing part.
4
Now we have to set the cooler in place. Before that, evenly apply a layer thermoprotei paste on the outer abutting surface of the CPU heatsink. Collect the laptop and immediately give him a little work.
Useful advice
It is worth noting that not all laptops require regular intervention for lubricating coolers. Some of it is generally not necessary, but some models are quite often start to make noise and to warm up.

Advice 2: How to lubricate a cooler in a laptop

High-quality cooling system of the mobile computer ensures stable operation of the important elements of the laptop. Timely service allows fans to extend the service life of these devices.
How to lubricate a cooler in a laptop
You will need
  • - silicone grease;
  • - Phillips screwdriver;
  • - cotton pads;
  • - metal blade;
  • - tweezers.
Instruction
1
Find out which cooler is not working properly. To do this install Everest, run it and open the menu "Sensor". Find the equipment, the temperature of which exceeds the norm.
2
Turn off the mobile computer. Disconnect the device from AC power. Flip the laptop and remove the battery pack. Now remove the necessary screws from the housing of the mobile computer.
3
Remove some devices that interfere with the normal disassembly of the housing. Most often before opening the case, you need to remove the hard drive, memory modules and the DVD drive.
4
Carefully separate the housing parts from each other. It is better to use a metal spatula. If you don't have this tool, use a screwdriver with a flat tip.
5
Lift one side of the housing and disconnect a few cables. This process should be conducted with tweezers or thin pliers.
6
Remove the lower part of the case and locate the fan. Unplug the ribbon cable of the power supply for this device. Unscrew a few screws and remove the cooler.
7
Siderite the sticker from the fan blades. Remove the plastic cover. With the help of forceps or needle pull the washer and rubber ring. After that, remove the blades from the axis.
8
Wipe with a cotton pad axle and fan blades. Apply a small amount of lubricant on the rotation axis. Install the blades and spin them a few times to evenly distribute grease.
9
Reinstall the retaining ring and gasket. Slip the end cap and attach the cooler to the radiator. Collect mobile computer in reverse order.
10
Turn on the laptop and after 20-30 minutes, run the program Everest. Check the temperature desired items.

Advice 3: How to lubricate the motor of an oven

When you turn on the fan , the stove can be heard howling, screeching, creaking or crackling. Even it may happen that the wiring is OK, but the fan is still not spinning. How to lubricate and clean the fan of an oven with his own hands?
How to lubricate the motor of an oven
You will need
  • - screwdriver flat or Phillips (depending on the specific motor heater);
  • - spanners of the required size;
  • - pliers;
  • - a few drops of any lubricating oil;
  • - new bushings (if you know what sleeve will fit);
  • - rag for cleaning;
  • - a little alcohol or gasoline;
  • - a hammer.
Instruction
1
Disassemble or remove the console of the car to gain access to the compartment of the fan. Disconnect the power terminals from the motor. Be careful not to break the contacts, which are attached to these terminals. Unscrew the nuts or screws holding the motor in the compartment.
2
Clear of the blade. If the fan blades are not attached with the nut, and tightly fixed on the shaft and remove them by hand does not work, then lightly heat them. For example, construction Hairdryer. A little plastic will soften and it will be easy to pull off.
3
Thoroughly clean the impeller from dirt. This will improve her balance and reduce bearing wear.
4
Disassemble the motor, using a screwdriver or wrench, depending on the model of the motor. For some models, housing parts are attached to each other curved antennae. In this case, carefully straighten them with pliers and a screwdriver.
5
Also there are models in which the location of the bearings is closed with a special removable plastic caps. To lubricate the bearings of such motors, it is sufficient to remove the caps and drip oil into the holes. If then the creaking of such a motor has not disappeared, it will still have to disassemble.
6
Clean dust from the casing and extracted the inside. Carefully inspect the bearings-bushings. Their increased wear may be the cause of jamming of the motor. If necessary, replace them.
7
Wipe the rubbing parts with alcohol or gasoline to clean them from dirt and old grease. After evaporation of the alcohol (or gasoline) apply a few drops of lubricating oil in place of friction. Excess grease remove the cloth.
8
Carry out the Assembly of the motor in the reverse order. Be careful: all the bushings, gaskets, and other parts that need to stand their ground. Otherwise, perhaps the accumulation of dust inside the motor, and as a consequence – failure. Install the motor into place, connect the power supply terminals. Observe the correct polarity. Otherwise, in the best case, the fan will blow in the opposite direction and would have to remove the console.
Useful advice
Any action make consciously, remember what and where to shoot. If in doubt, remember that everything is correct – take notes on paper.

Advice 4: How to lubricate a cooler computer

A clogged cooler is one of the most common causes of overheating of certain hardware on your personal computer. Timely care of the fans helps extend the life of PC and laptop.
How to lubricate a cooler computer
You will need
  • - Phillips screwdriver;
  • - silicone grease;
  • - engine oil;
  • - cotton pads.
Instruction
1
Turn off your computer and Unscrew the few screws holding the left side wall of the housing. Take the wall and turn on the computer. Let's see what the coolers are spinning fast enough. Sometimes the content of dust in the fan also can be identified by the unpleasant sound emitted by this device.
2
Turn off the computer and disconnect the cable from the power supply. Now, using a Phillips screwdriver, remove the screws holding the fan to the radiator for cooling. Unplug the power cable of the cooler. Usually it is connected to the motherboard or the device on which is mounted a fan.
3
Remove the cooler from the housing of the system unit. Now carefully remove the sticker located in the Central part of the fan blades. There are two basic types of coolers. In the first case, you see the hole in which the axis of rotation of the blades.
4
Pour a small amount of machine oil (silicone grease) into this hole. Move the blades to allow the lubricant is evenly distributed on the axis.
5
If you're dealing with fans of a folding type, remove the plastic cover covering the same hole on the blades. Using tweezers or a thin metal object remove the rubber ring and the plastic strip with the axis of rotation.
6
Remove the fan blades off the shaft. Apply a little grease in the hole. Now lubricate the axle. Be sure to remove the dust from it, if present. Assemble the cooler. Attach this unit by using the previously unscrewed screws. Connect the power supply.
7
Turn on the computer and make sure that the fan is working properly. Install the program, allowing to obtain data on temperatures important devices PC. If some equipment is still very hot – need to replace the coolers.
Search
Is the advice useful?