You will need
  • Mounting plate
  • The fabric for the pattern (Voile)
  • Paper patterns
  • Thread
  • Scissors
  • Mel
  • Pins
  • The main fabric
Instruction
1
The process of creating a pattern svaga begins with the purchase of a working material for the construction of the template. Voile you can make a test model, which will form folds. After that you will be able to transfer the final version to the fabric from which you plan to sew.
2
The basis of the pattern svaga equilateral is an isosceles trapezoid. You need to draw half of a trapezoid. Measure the height of the future Smad. Pelmets on the Windows in the model homes rarely sew with a height of more than 50 and less than 30 cm will Take the approximate height of 45 cm as Smad is a semicircle with a clearly laid pleats, the height we multiply by a factor of folds, which is equal to three. Consequently, 45 cm x 3 = 135 cm Is the height of our trapezoid.
3
The next value is half of the top peracid, or ½ of the upper side of the trapezoid. Look at your window, imagine how much of Smad you need to register it, and approximately what should be the distance between the folds of each Smad. At a height of 45-50 cm Smad, looks the most organic the width of the upper parecida equal to 30 cm so, AB = 30 cm.
4
The next point in the pattern is the depth of the first fold. This value is also taken arbitrarily, it is equal to 5-7 cm Mark on the drawing point A1. Now we need to shift the overall height of Smad to the depth of the first fold. Put the point B1.
5
Then determine the length of the sagging Smad. Take the cord and simulate with it overhang the bottom edge of the Smad. Simply fit the ends of the cord on the bracket. The deepest point of the SAG of the cord must be equal to 45cm. Don't forget you are modeling themselves swag, and do it to suit your taste. Measure the length of cord dangling between the two pins. Divide it in half.
6
Swipe in from the point To the perpendicular. Mark on it a segment equal to half the length of the cord, and you get the point G. Connect the points B1 and G a smooth semi-circular line. You got the drawing 4 main points forming the future pattern: A1, B1, G and B. Connect points B and G in Front of you half a paper pattern.
7
To svag well-draped, cut it on the bias. Fold bought a piece of the veil at an angle of 45 degrees. Pin the pattern, positioning the segment A1B1 by the fold of the fabric. Add 1 – 1.5 cm for seams and take the desired part. Mark on the fabric the middle of the pattern.
8
Make a mark on the bracket. Swipe down perpendicularly a straight line. On this line you will target mid-Smad, in order to avoid distortions.

Fasten the wall mounting plate upper peracid three pins, aligning the middle mark on the bracket. Extreme pin plug, departing at 7-9 cm from the edge of the fabric. Lay the first fold and secure it with pins on both sides. Align the fold with your hands, pay attention to the middle crease was exactly above the vertical line that you have conducted. In the same way as to lay the pleats over the entire length of the shoulder, and fastened them with pins. Approximate depth of each fold – 5-7 cm Try to make the folds equal.
9
Stepping back a few steps, decide which shoulder you have turned out better. Sew with small stitches the folds in it from his grasp. Stepping back from the weld at 2 – 2.5 cm, cut the excess fabric. Remove the template from the mounting Board. Remove the pins and a running stitch. Fold the fabric along the center and cut the second shoulder, so that the pattern was completely symmetrical. Expand the fabric and iron it iron. Before you finished pattern-the pattern of an equilateral Smad. Using it, you will have plenty of Smad as much as you had planned in his model of the pelmet. Now we can calculate how much fabric you will need and go to the store.