Advice 1: How to install speakers in the "Prior"

In the new Lada Priora native speakers are only available in the maximum configuration. But these cars are not in great demand among buyers due to high cost. In all other cases, set to music in the car you will need.
How to install speakers in the "Prior"
You will need
  • Screwdriver;
  • - screws;
  • - duct tape;
  • - jig saw electric.
Instruction
1
To install speakers in regular places in the doors remove the trim panel. Of the prepared arch, remove the foam end caps which are installed to reduce noise during movement.
2
In the doorway is the OEM wiring harness of the car. Detach the two wires with terminals – large and small. These wires go directly to the radio. Wire terminals connect to the speaker. It has a special output under these terminals.
3
Insert the speaker into the niche and secure it with screws. Put the door trim and screw on caps. In the same way connect the speaker on the other door.
4
Install rear speakers. The wagons or hazakah provides a regular place for speakers with a radius of 13 cm.
5
With the plastic console in the trunk remove the screen under the speaker. Fold the fabric covering the rear pillars. Inside, there are harnesses with wires. From the harness running along the right front, disconnect the two wires with large and small terminals and connect to the right speaker. From the harness running along the left rack, connect the wires to the left speaker. Connection diagram is the same as when installing front speakers
6
Insert the speakers into place and secure them with screws. Top set the grid.
7
Sedan standard seats under the rear speakers are not provided. So you can put speakers of different radius: 13cm, 16cm, 18cm or 6 to 9 ("ovals").
8
Remove the rear cargo shelf. Mark her place under the dynamics. Electric jigsaw to cut out the holes according to the planned lines.
9
Under the skin the rear pillars, locate the harnesses with the standard wiring. From the harness running along the right front, disconnect the two wires with large and small terminals and connect to the right speaker. From the harness running along the left rack, connect the wires to the left speaker.
10
Install the speakers in a prepared niche and secure them with screws.
Note
If the regular wires do not reach the speakers, they can build with the help of special wires to speakers.

Advice 2: How to install speakers in front doors

The acoustics in a modern car is very important. The drivers usually install a car stereo and two speakers ago. But the special music lovers prefer to embed speakers still in the front door. This increases the overall volume and allows you to fully enjoy the music. Speaker installation in front doors - employment is difficult and requires patience and skill.
How to install speakers in front doors
You will need
  • - columns of type "pancakes";
  • - drill;
  • jig - saw;
  • - duct tape;
  • - screws.
Instruction
1
Disassemble the front door panel. To do this, Unscrew the interior door handles and remove the panel. It is secured with clips. The best place to put speakers is the lower right side. In this location the speaker will not interfere with door elements, such as glass door locks and handles door opening. But you can install at any place of the door if desired.
2
Saw out the hole for the speaker. This should be done with a jigsaw for metal. The hole should be the diameter of the dynamics of a few millimeters. This is necessary to ensure that the column was a tight hole. Thereby creating an independent fixation dynamics in a door. Immediately saw a hole in the door panel. Before that, right space bar, otherwise you don't get holes.
3
Make a mount for the speaker. This is the most critical part of the job. Properly mark the location of the future dynamics. To strengthen you should use the plates that will be screwed to the door with screws. The same screws will attach the speaker to the plates. You need to accurately choose the size of the plates, otherwise the speaker will be much bulge. Such plates should be four. Each of them is fixed in its angle. Also you can cut a ring out of plywood and insert it into the cut hole with glue to secure it, then install a speaker into this ring and secure with screws.
4
Drill a small hole in the inside of the door where there are hinges. Next, drill another hole opposite the first. Here we need to extend the wire from the radio to the speakers. Hide them under the bar while pulling. At the junction between the two holes of the door, put the wire on PVC tube. This will prevent cutting the wires on sharp edges of drilled holes and a further circuit. Connect the speaker and assemble the panel. During the connection, insulate the exposed places with electrical tape. Otherwise you can not avoid circuit.
Is the advice useful?
Search