Advice 1: How to connect a reversing camera

Today auto shops offer car owners a large range of rear view cameras, monitors and services for the installation of the camera in the car. However, nothing prevents to install the camera yourself. If you follow the instructions, the camera monitor will delight for a long time. The selection of the optimum location of the camera and monitor depends on private tastes and preferences, but the electrical schematic for all variants is the same.
How to connect a reversing camera
You will need
  • 1. Camera and monitor
  • 2. Pre-made wires with connectors
  • 3. Fuses (2 PCs.) at 0.5 A
  • 4. Screwdriver
  • 5. A set of keys
  • 6. Knife
  • 7. Pliers
Instruction
1
Before beginning of all work, remove the positive battery terminal.
2
Consider the Luggage: regardless of the model, the camera should be the wires (connectors) power and videoyoustroke. Most often recommended to bring power to the camera from the rear of the stroke, with the result that the camera will work only when reversing. Rear view camera is designed for short-term use, and failure to do so can drastically reduce its service life.
3
Connect the red camera wire to the positive terminal of a lantern of a back stroke. If the camera wire there is no fuse, install it. The fuse should be a nominal 0.5 A, and be located as close as possible to connection point.
4
Black (negative) wire the camera connect to the back of the car. For example, under appropriate and pre-stripped bolt. The fuse for the black wire is not required.
5
Most cameras are equipped with a yellow five-meter wire to connect to a monitor with typical audiovideocenter connector. If the cable length is not enough to strip the interior of the car, get an extension cable with the connector of connectors. You can purchase a suitable cable and to solder the necessary connectors.
6
The cable connect to the monitor, inserting it into the video input. Note that each monitor or receiver may be several video inputs, one of which is specialized to connect a rear view camera. Find the right video input it is possible for the user to monitor (radio). The simplest monitors are just 2 connectors: video output (most often white) and video input (often a yellow color).
7
The monitor is also required to provide meals. Act as if the camera is connected: the red wire with fuse on plus power, black to ground (under the stripped bolt).
8
After a thorough check of the work done, the connectors are wrapped with electrical tape. Don't forget to include the positive terminal of the battery.
Note
1. Immediately after the purchase, test the camera and monitor.
2. Incorrect connections may cause damage to the camera.
3. Save on the fuses can cause a short circuit in the whole electrical system of the car.
4. Before something somewhere to plug in, check it with a multimeter (tester). Multimeter to spoil anything, but a light bulb (controlkey) easily.
Useful advice
1. To power the camera necessary wires, designed for rectified stabilized voltage of 12 V and current of 0.7 A. Coaxial cable for signal transmission from the camera to the monitor, you can get the same used to connect the antenna to the TV.
2. To protect the power supply cables and signal transmission using the washer hose. Route the wire inside the hose and wrap outputs with connectors with electrical tape.

Advice 2 : How to connect rear view camera

Rear camera viewconnected to rear gear will allow you to see what you do not see the usual sensors. You can customize the height and angle of the image. The camera can notice all the low curbs and stones as well, your bumper will remain without a scratch.
How to connect rear view camera
You will need
  • Side
  • Tester or continuity test
  • Drill
  • Screwdriver
  • Duct tape
Instruction
1
To connect the rear camera view needed a radio with a built-in monitor on which the image will be transferred.
2
Rear camera view are: built-in lights illuminate the room, embedded in the bumper in the form of a spy-hole built into odnomernoi frame.
3
Install the camera at the selected location. From the camera should go 4 wires (included), one of the wires double. Two wires connect to the reversing lamp: to ground and 12V power.
4
Other cables route to the radio - it will transmit the picture from the camera. Stretching the wires through the interior from reviewing plastic door sill or on top around the edge of the ceiling. To do this, remove the door rubber seals, lay the wires and re-insert the seals in the door.
5
On the radio on the rear wall find an input for a camcorder. Connect one double wire.
6
So that when reverse gear automatically switch on the camera, the radio must be connected to the wire at the rear of the transmission. To this end, the standard wiring harness of the car we need to find the wire coming from the transmission. This can be done with a multimeter or continuity. Put her in reverse and test which of the wires appeared +12V.

Advice 3 : How to connect camera surveillance

In our turbulent times the use of different surveillance systems have become an integral part of life. Cameras are everywhere: at work, in shops, cars and ATMs. To install such a camera is not difficult, and the information send to the computer from which then it will be convenient to view the entry.
How to connect camera surveillance
Instruction
1
Install the camera outdoor surveillance, according to the instructions. Connect it using the cable supplied. However, there are video cameras that connect via a network cable and switch. Therefore, before you purchase the camera surveillance, ask the consultant how and what to connect the selected device.
2
Well hide and insulate the wires leading from the camera to the computer to avoid accidental breakage or damage from natural factors (wind, rain, cold).
3
Connect the camera to the computer. To do this, plug the cable into the cable connector to your LAN. The operating system will automatically detect the new device and will require drivers for its installation. Use the software CD that is also included in the kit.
4
Insert the disk into your computer and install all the components. After the installation is complete on your desktop will appear a shortcut from the camera - click it twice and run the program. In the service tab, make the necessary settings.
5
Specify the folder in which you save all recordings from the camera surveillance. On the drive that contains this folder, there should be more free space. Recommended even to use a separate virtual disk for this purpose. In the case of infection by computer viruses or system error the disk can be encrypted.
6
Use licensed software to prevent the possibility of breaking your system videosurveillance via Internet. When properly connected the camera to the computer, there will be constant monitoring of the protected area. Thus, you can protect your home, work or car from unwanted intrusion.
Is the advice useful?
Search