Advice 1: How to tie waistcoat knitting for baby

Tie for her little children colored vest spokes. He fit the facial surface with different colors, and each colored area must be separate from the coil. Changing the colors, you need to cross the threads on the reverse side of the work to vest no openings.
How to tie waistcoat knitting for baby
You will need
  • - 50 g yellow, orange, blue and green yarn Licorne (100% mercerising cotton, 120 m/50 g);
  • - knitting needles No. 2 and No. 3;
  • - the spokes on the line No. 2.
Instruction
1
Begin to knit the vest from the back. To do this, type 32 loop orange thread and 32 loops of blue thread and knit the front stitch between the edge while you change colors.
2
Using 10cm from the edge of typesetting start knitting on the first 32 loops of yellow thread and the remaining loops of green thread. 13 cm close both sides for armholes, one time for 3 loops in each 2 row 1 three times, 1 two times and 3 times one loop. And in 23 cm close to shoulder bevels on both sides once at four loops in every second row 2 times in three loops.
3
Now with the beginning of the bevel shoulder at the same time close to neckline average eight loops and both sides finish separately, while in the second row close to the inner edge of one times seven loops. After 24 cm from the edge of typesetting close all the loops.
4
To perform the right type of shelves 31 loop orange yarn and knit the front stitch between the edge. After 10 cm from the edge of typesetting start knitting thread green. On the left side at the same height, run the armhole and a bevel shoulder as on the back.
5
Then after 20 cm from typesetting edge close the the right side of neck once three stitches in every second row, one times three, one two times and two times in one loop. At the height of the backrest to close all the loops. Left shelf knit symmetrically, only it should start blue and end with yellow thread.
6
The vest is almost ready. Now run the shoulder seams. For the neck strap dial 9 loops orange thread and tie a 20 cm rubber band, then close the loop. Then sew the placket to the neckline.
7
For trims armholes dial at the 9 loops orange thread and tie 24 cm rubber band, then close the loop. Next sew the strips to the armholes. For plank shelves right enter 9 loops orange thread, 10 cm green thread and 2 cm orange thread, again close the loop. Sew the strap to the right shelf.
8
Finally, for the strap of the left shelves, dial 9 loops of blue thread and tie a rubber band 10 cm blue thread, 10 inch yellow thread and 2 cm orange string. Hinges close. Sew the strap to the left side. Follow the side seams.

Advice 2: How to knit a bevel for shoulder

When knitting products with vtachnoy sleeve is to perform bevel shoulder. This is particularly important in the manufacture of blouses and dresses of thin yarn. In this case, the disadvantages of a cut is very noticeable, and almost impossible to hide. Such products are best to knit the pattern, making the exact calculation loops.
How to knit a bevel for shoulder
You will need
  • - nadopasana detail of the product:
  • - thread crochet:
  • - the spokes on the thickness of the threads;
  • the pattern of the product;
  • - a sheet of paper and a pencil.
Instruction
1
Construct the pattern items on the graph paper. This is more convenient because it allows faster and more accurate to perform the calculation hinges on any increase or decrease of the width of the part. Find the pattern at the beginning of the beveland shoulder , and slide And from that point of straight line L, perpendicular to the median line of the part. Depending on the style of this video or come to one of the points of the neck or to the middle line. From the point of the base of the neck In (it is located where the beveland the shoulder goes into the neckline) let the line L perpendicular. Denote the point as S.
2
Before knitting make a precise calculation of the number of loops on row width and number of rows in height of the product. Measure all the segments of a right triangle ACB. Count how many loops you need to remove and for a number of rows. In this case, note that the close-loop you have to either at the beginning or at the end of the row, so the resulting resultat divide by 2. The number is designed to close loops divide by this value. If unable to divide evenly, 1 to 2 loop residue, close to the first row. If more — distribute them evenly.
3
Knit bevel in two ways. In the first case, in the beginning of the row, close the number of loops obtained by dividing. Davaite the series to the end, turn knitting, tie a number of full and early next again, close the desired number of loops. So follow these and all the remaining rows.
4
In the second case, the beveling is performed to the cropped rows. Dawasa a number almost to the end, leave on the left needle as many loops as happened in the division. Flip the work and the second row provarite completely. The third in addition to nepovezane leave it on the needle the same number of loops. In the last row, close all the loops. Crochet openwork products with a complex calculation drawing is preferable to this method. It allows you to continue the pattern, almost without changing, until the very end.
Useful advice
Build patterns for crochet are the same. The bevel is made at the end of the row. You just make a number shorter than the previous one to the desired number of columns.

To perform a bevel is required on all items the same way.
Is the advice useful?
Search