Advice 1: How to pull the batteries

The fence, constructed of mesh netting, is one of the most popular types of fencing suburban areas. And this is understandable. This material is practical, reliable, affordable and easy to install. How independently to pull the mesh netting?
How to pull the batteries
You will need
  • - mesh netting;
  • metal or wooden poles;
  • - metal cable;
  • - wooden stakes;
  • cord;
  • - gravel;
  • - sand;
  • - shovel;
  • - nails or staples;
  • - hammer;
  • metal hooks or clips
  • welding machine
Instruction
1
Measure the borders of the plot and count the number of consumables. It is necessary to drive wooden stakes at the corners of the plot and pull them around the perimeter, cord. Measure the length of the cord - it will match the required length of mesh netting. Calculate the required number of posts, based on the fact that they must be installed with an interval of 2,5-3 meters.
2
Select the mesh netting. Note that the width of the grid should correspond to the desired height of the fence. To install the temporary fence you will approach the mesh of black wire. Its price is considerably lower. But if the design will be used for a long period of time you need to buy a more expensive ocynkowany option. A fence made of such material can last more than 20 years.
3
Install posts. To do this, dig a pit depth of one meter. Pour the gravel and sand on the bottom of the pits and carefully tamp. Install posts and fill the holes with soil, tamping it.
4
Install a roll of mesh fencing around the corner post and secure it the edge. If you purchased a non - grid - pick up the edge at 5-10 cm above ground level. To ensure that the mesh is securely held on the metal poles, it is recommended to weld the hooks to them. Another mounting method is to use a special pipe clamp. Of course, you can do much easier and bind the mesh to the posts with wire, but this mounting option is much less reliable.To attach the mesh to the wooden posts you can use special staples or nails.
5
Carefully unwind the coil, pulling the mesh, and attach it to next post. Pull the metal cable at the bottom and the top of the net and fasten its ends to the pillars. This technique allows to avoid sagging of the mesh netting. Make a fence around the perimeter of the site, using the same method.

Advice 2: How to mount batteries

Mesh netting is easy to use, economical material that allows you to quickly mount the fence without resorting to professional assistance. Fence mesh-netting is a lightweight design that does not obscure the plants in the garden, thus reliably protecting it from intrusion.
How to mount batteries
You will need
  • level;
  • - wire;
  • - fittings;
  • - the cable.
Instruction
1
To secure the mesh-netting, you need to mount the basis for the future fence. Usually the fence netting are doing on metal or wooden poles, which are securely embedded in the ground.
2
Prepare the poles for attachment mesh-netting in advance. If it is wood, it must be sanded, treated with a special waterproof mastic. Metal posts cleaned of rust, coated with paint or mastic for metal, as welded hooks for mounting the grid is the best option if you plan to do stretch the fence from mesh-netting.
3
If you are going to frame a fence, except the posts need a frame for mounting the grid. The frame is made from wood, welded metal parts or profiles. The height of a single frame from 1 to 2 meters in width, it is better not to do more than 3 meters. Once the frame is ready, to him by means of clamps or a thin, flexible wire, attached the wire-netting. Finished frame with stretched mesh clip on dug into the ground and concreted the posts better.
4
In case you have chosen the easiest form of a fence from mesh-netting – stretch, you have to first dig all the poles, starting from a corner, and then attach the grid directly to the post. It is either fixed in advance to the welded hooks or if the hooks on the posts there, gets attached to them with clamps or wire.
5
Pull the grid needs as much as possible so she does not SAG. First, bind the edge of the mesh to the post and only then pull it and attach to the next post. Raise the mesh above the ground a few inches, if you want to protect it from excess moisture -- if the stack is constantly in contact with moist soil, it will rot quickly.
6
The upper edge of the better to pass through the mesh of thick wire, wire rope, fittings – this will also prevent the mesh from sagging. It will be useful also if you miss the wire and through the lower edge.
Is the advice useful?
Search