Advice 1: How to connect telephone cable

The need for splicing telephone cable occurs when it is open (e.g. during repair of an apartment), and if the phone socket moving to another place, and the cable must be lengthened. To be able to perform this operation every home should master.
How to connect telephone cable
You will need
  • cutters;
  • - rubber gloves;
  • - duct tape.
Instruction
1
Remove the tube on parallel phone, which despite a broken cable left connected to the network. This will prevent the strike voltage ringing that may appear on the line in case of receiving an incoming call. If you only have one camera, or breakage happened in a place that was disconnected all the phones in the apartment, have to work in rubber gloves.
2
Find the location of cable damage. If you visually can not find it, use contactless inductive fault finder. This device can borrow the telephone operator. If this is not possible, the cable cut, the break is unknown, it is easier and faster to replace the whole thing.
3
For splicing the two-wire flat cable the old design with each of the parties will razdvoenie "noodles" along the cutters so that the cut line was exactly in the middle. Tips to gently clean. Remember that insulation "noodles" is not made of PVC, and polyethylene, so when you sweep accurately calculate the effort to remove only the insulation without damaging the conductor.
4
One of the wires of one end of the cable connect with any of the wires other end. The polarity is correct when it is unnecessary. Then do the same and mix with the remaining wires. Carefully insulate the joints from each other. Then verify that the numbers, which after breakage stopped working again.
5
Telephone cables of the new design have an outer shell, within which are laid in a row two or four stranded conductor, each of which has its own colored insulation. The outer shell is easily removed with almost no risk of damage to insulation of conductors.
6
If the cable is two-wire and the procedure for splicing is same as for the "noodles". Four-wire cable, which is more common, repair the following: last wire in the series will not connect or even not clean because they are not involved, and the wires in the middle, crystite in the manner described above.
7
If the line is connected to a special telephone designed to work simultaneously with two lines (they are found, though rarely, in the offices of the leads may also be involved. Splice into this line, simply connecting the conductors of the same color.
8
After work and making sure that all the phones are reconnected to the line, place the handset on the device from which you removed before working.

Advice 2: How to connect phone cable to phone socket

You want to install a wired telephone in a convenient location, but there is no socket to connect it? To set it quite easy. Doing this operation will take much less time than exhausting waiting for a telephone operator.
How to connect phone cable to phone socket
You will need
  • - telephone outlet;
  • - screwdriver;
  • cutters;
  • - telephone cable;
  • - cable box;
  • - screws;
  • - screwdriver.
Instruction
1
The installation of additional phone sockets in some cases can be avoided. For this you will need to acquire for your phone cord is of such length that it is enough to connect it to the existing outlet. To connect devices with non-removable cord, you can use a phone extension cable.
2
If you do decide to install an additional outlet, it is necessary first of all to acquire. They are of two types: miniature RJ-11 and large RTSC-4. Let's see which fork has your phone and choose the appropriate outlet. At the same time get a phone cable and cabletion box of the desired length and screws.
3
Take the cabletion box and secure it with screws on the way from the existing telephone socket to the installation of the new. Swipe inside the box cable, and then close it.
4
Screw the new socket to the wall. Connect it to the cable in the following way. If it's socket type RJ-11, the conductors of the cable connect to the two middle contacts, and two extreme Express free. If is set the socket type RTSC-4, open the plug your phone and see how the contacts are connected the wires. To the same contacts of the plug and the conductors of the cable in the socket. For reference: standard outlet RTSC-4 wires is commonly connected to two right contacts, but this requirement is not always observed. Close the plug and socket.
5
Pull the old outlet. Lift the handset of any parallel phone in the apartment below in the line was not able to do the ringtone, capable of causing electrical shock. Connect the new cable in parallel with the old. Close the socket and place the handset on the parallel phone.
6
Connect the phone to the old outlet. Make sure it is earned. Also make sure that the other parallel devices are not lost efficiency.

Advice 3: How to connect 2 sockets

Of all the known electrical switching devices the most common are the outlets whose main function is to make reliable contact with the plug of the device connected to it. The number of used electric appliances with each passing day it becomes more and more, the number of sockets in the room remains unchanged. To lighten the load on one of them allows the connection to the second outlet, and not to pull extra wires from the electric unit, you need to combine them together. To make it easier via parallel connection.
How to connect 2 sockets
You will need
  • - a multimeter or the indicator;
  • - soldering apparatus;
  • - screwdriver set.
Instruction
1
The parallel connection of the sockets is the safest, and therefore most popular. Besides, it is easy to carry with their hands. But we must remember that it is only suitable for the outlets belonging to the same group.
2
To start off the machine to remove the plug outlet voltage. This can be done by loosening the tube, if used, or by turning off the circuit breakers on the input.
3
Check the absence of voltage. You can use the usual voltage tester, multimeter or indicator. Just making sure there is no voltage, you can remove the cover from the outlet and touch his hand to the bare wires and contacts.
4
Connect the electrical socket parallel connection via junction box or using the terminals. The second method is also called Sleipnir connection. When using the loopback cable is connected to the first unit block and the cable for the next block to be energized from the latter.
5
For slavnogo connections is very important to disconnect the outlets were independent from each other. Connect conductors with zero conductors through terminals or soldering. To the first electrical outlet connect the zero and phase. After that, check the clutching to the ground wire. From him to each of the electrical units will be supplied grounding wire for.
6
To connect the second socket, connect the a phase and working zero from the last unit of the first block and the gripping, infinitely adjustable and connect the ground wire.
7
After works will be finished and working parts are reliable outlets installed in the escutcheon, you can tie the cap and turn on the machine.
Note
Materials all used wires should be identical. For example, it is impossible to connect with copper wires made of aluminum.

If you cannot avoid connecting the wires, made of different materials, it is important to make their taludevahe before connection.
Useful advice
The implementation of the parallel connection requires the contractor's compliance with safety regulations, and therefore it is important not to lose sight of even minor details.

When connecting wires to the contacts necessary to turn the end of the wire to form ring.This is required to create a sufficient platform for the contact.
Is the advice useful?
Search