You will need

- - the tape;
- yarn;
- - spokes.

Instruction

1

To increase the size of the model required increasing the number of loops. It's easy to do things when knitting, which uses a simple binding, for example, facial surface, garter, rice and so on. To calculate the required number of stitches for knitting in this case, make the sample yarn, which will knit the model.

2

Next, count how many loops within a 10 cm sample and divide this number by 10. Thus, you will receive the average number of loops in 1 cm. If you have not a whole number, not round it, as otherwise the calculation will not be accurate.

3

Define the width of each part in inches. This number, multiply the number of loops in one centimeter. Get the required number of loops for stacked series.

4

If your model uses a fancy pattern that fit the scheme that knitting did not cause any problems, and the pattern was located in the place where conceived, changing the number of loops should be commensurate with his rapport.

5

Link the sample, as described above, make the necessary measurements and count the number of loops in the part. Then count the loops within the repeat. Divide this figure by the number of rapport in detail. Integer – as full of rappaports have to be repeated in detail.

6

The remaining number of loops and divide by two. These loops are knit at the beginning and end of the part, first, starting from the end of rapport. For example, if your calculations 38 loops for the knitting pattern and there are 10 loops on which you want to increase the detail. Therefore, divide 10 by 2 get 5 loops. The repeat count of the last 5 loops and start knitting the details with them, then repeat rapport and provarite 5 loops of the beginning of rapport.

7

In the case when resizing differ slightly, the neck and knit armhole, as indicated in the description for the largest size. If the change more than two dimensions, then in the middle of the front and back, close the greater the number of loops that extend back, in front of the product and the detail of the sleeve.

# Advice 2 : How to increase the pattern of the pants

Many of us would like to learn how to professionally sew. It is not only the ability to dress nice and trendy yourself and your family members and make a profit. Magazines offer us the latest models, and high-quality fabrics can make your stitched things significantly better than those that are sold in stores. However, the sewing - it's not that simple, there are many nuances that must be mastered. Consider this question on the example of the pants.

Instruction

1

Learn to resize patterns

The length change at anterior and rear halves of the pattern correction in three lines, marked perpendicular to the grain lines. On the first lines, which are at 15 cm below the waist lengthening make 1 cm For the second set of lines that are in the middle between the level of seat height and knee extend 2 cm In the third lines that are in between the height of the knee and lower shear elongation do 2 cm

The length change at anterior and rear halves of the pattern correction in three lines, marked perpendicular to the grain lines. On the first lines, which are at 15 cm below the waist lengthening make 1 cm For the second set of lines that are in the middle between the level of seat height and knee extend 2 cm In the third lines that are in between the height of the knee and lower shear elongation do 2 cm

2

Also, if the person is different from the growth indicated on the pattern, it is possible to calculate the change in length in the following example. For example, you change the length of the pants the pattern on the growth of 160 cm height 174 cm

First, find the difference between growth and growth patterns, in this case it will be 14 cm find the magnitude of the ratio (14:8 =1.75). Extend the pattern to 1.75 on the first lines of 3.5 (1.75*2) for the second set of lines and 3.5 on the third lines. The very lengthening of the spend so. Apply the three adjustment lines on the front and rear halves of the pants and cut the pattern along these lines. Spread of the pattern at the cutting lines at the desired lengthening distance and mount them on strips of paper.

First, find the difference between growth and growth patterns, in this case it will be 14 cm find the magnitude of the ratio (14:8 =1.75). Extend the pattern to 1.75 on the first lines of 3.5 (1.75*2) for the second set of lines and 3.5 on the third lines. The very lengthening of the spend so. Apply the three adjustment lines on the front and rear halves of the pants and cut the pattern along these lines. Spread of the pattern at the cutting lines at the desired lengthening distance and mount them on strips of paper.

3

Increase the width of the product

Increase the width of the pants on the bottom. For example, the width of the pants at the bottom have any model 40 cm, and you need 45 cm, so the difference is 5 cm Increase front and rear halves by the same amount (in this case 2.5 cm on each half). The amount of extension, divide in half, add the lack of width uniformly, stepper and lateral slices (in this example 1.25 cm). Change the width of the pants at knee level expect by analogy with the change of the width of the pants on the bottom. Gradually remove the line expanding from the knee level to the level of the seat height.

Increase the width of the pants on the bottom. For example, the width of the pants at the bottom have any model 40 cm, and you need 45 cm, so the difference is 5 cm Increase front and rear halves by the same amount (in this case 2.5 cm on each half). The amount of extension, divide in half, add the lack of width uniformly, stepper and lateral slices (in this example 1.25 cm). Change the width of the pants at knee level expect by analogy with the change of the width of the pants on the bottom. Gradually remove the line expanding from the knee level to the level of the seat height.