Advice 1: How to repair a broken sole

Unfortunately, the Shoe sole sometimes crack. Typically, overlays, installed the crack, do not give the desired result - the footwear continues to get wet, and "patch" quickly falls off. How to repair a broken sole?
How to repair a broken sole
You will need
  • - acetone or gasoline;
  • - sandpaper
  • camera from the bike.
  • rubber adhesive;
  • - boot knife;
  • - soldering iron;
  • - kapron.
Gently clean the soles from dirt and dust. Thoroughly coat the inside crack surface with sandpaper. Wipe with acetone or gasoline to degrease.
Cut the edge of the sole around the crack to a width of 5-7 mm using a shoemaker's knife. The depth of cut shall be one millimeter.
Carefully measure the depth of cracks in mm. Add to this the value of 15 mm. Take the old bike camera, and cut from it a strip, the width of which will correspond to the result obtained.
Strip the strip with sandpaper. Degrease using gasoline or acetone. Miss a strip of rubber adhesive on both sides. While on the one hand the adhesive must cover the entire surface and one must leave the edges dry. The width of these edges should be 5-7 mm.
Take shoes that need repair, and bend it so that the crack on the sole as disclosed. Carefully apply glue to the damaged area and let it dry for 10-15 minutes. To close the rift when it should not.
Take a strip of rubber and bend it in half. Gently put in a broken sole and straighten shoes. Firmly press the edge of the strip protruding from the cracks to the bottom. Put the shoes under the load for 24 hours.
Repaired in this way, the shoes will serve you.
Pour a broken sole, molten nylon. Dry, clean and degrease the crack. Heat the soldering iron and slide it across the inside surface of the damage. The leather or rubber from which the sole will start to bubble and become sticky. Take a small piece of nylon, apply to the crack and press it with soldering iron. RUB the melted nylon in the damaged area. Repeat this process until until the crack is completely gone. Note that to spread the melted nylon does not need a hot nose of the soldering iron and its handle.

Advice 2 : How to repair the soles of shoes

Of all component parts of the Shoe most likely to damage and wear prone to sole. Method of repair depends entirely on what material it is made and how is attached to the top of the Shoe.
How to repair the soles of shoes
You will need
  • - Gasoline
  • glue 88Н
  • Shoe spokes
  • - dratwa
  • Shoe options
  • Shoe rasp
  • pieces of polyurethane
The place where the departed polyurethane sole, clean from dust and dirt and degrease with gasoline. Then at the same location, remove the flat needle files painted a layer of skin, and again perform degreasing. Heat the electric soldering and gluing on the skin and smooth cut from the soles of old pieces of polyurethane. Squeeze the top of the Shoe and sole , and hold them heated part of the device for a burning out, treat the area of bonding. While zaglubljaja heated element to postilki. It is important to precisely follow the temperature of the heating device and the pressure between the top and sole, which will require a certain skill.
If the edge is overlaid with polyurethane soles up, on the cleared and fat-free area, apply a layer of glue. Then soak 15 minutes, squeeze the sole to the top of shoes and sew grated Shoe pitch stitch. The seam must go to a distance of 5 mm from the top edge. If unstuck sole – rubber, skim the repair, apply the glue and after 15 minutes of drying pressure-tested shoes.
If the rubber sole is drifted, it is necessary to align the Shoe rasp and degreased gasoline. Also degrease the soles of finely porous rubber. Cover the trail and the sole of a thin layer of glue and, after 10 minutes, glue the way forward. Acting for the sole edge of the track cut away with a knife, align the rasp and smoothen the abrasive cloth.
To repair the leather solesneed sole of similar material. Place the sole on a metal surface such as iron or an iron anvil, with flesh side up. A heavy mallet with a large bacom, emboss it, starting from the middle. Place embossed soles on the soles and at the time we secure it with a couple of nails. Cut the edge and sew, pre-cut by one-third the thickness of the groove in which the seam will be hidden. Sew a sole using a Shoe needle stitch, grated shoemaker's pitch. After sewing it over the slot with glue and hammer to close it.
Is the advice useful?